Martin Exterior 1200 Wash Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 84

Martin Exterior 1200 Wash Скачать руководство пользователя страница 4

4

Exterior 1200 Wash user manual

1.1 Safety information

The following symbols are used to identify important safety information on the product and
in this manual:

DANGER! This product is for professional use only. It is not for household
use. If safety precautions are not followed, it presents risks of injury due to
electric shock, heat and ultraviolet radiation burns, lamp explosion, falls,
high-intensity light, and fire.

Read this manual before installing, powering, operating or servicing the
luminaire. Follow the safety precautions listed below, and observe all
warnings in this manual and on the luminaire. Use the luminaire only as
described in this manual and in accordance with local laws and regulations.
Refer any operation not described in this manual to a qualified technician.

Electrical safety

• Do not use the luminaire if any cable, component or cover is damaged, cracked or

deformed.

• Switch the lamp off, allow the luminaire to cool with fans running for 20 minutes, then

isolate it from AC power and lock out power before removing or installing the lamp,
fuses, or any part.

• Ensure that the luminaire is correctly configured for the local AC power voltage as

described in this manual before applying power for the first time.

• Always ground (earth) the luminaire electrically.

• Use only a source of AC power that complies with local building and electrical codes and

has both overload and ground fault (earth fault) protection.

WARNING!

Read the safety precautions in this section

before installing, powering, operating or

servicing this product.

DANGER!

Safety hazard.

Risk of severe

injury or death.

DANGER!

Refer to user

manual for

important

safety

information.

DANGER!

Hazardous

voltage. Risk of
lethal or severe

electric shock.

DANGER!

Fire hazard.

Warning!

Burn hazard.

Hot surface. Do

not touch.

Warning!

Risk of eye

injury. Safety

glasses must

be worn.

Warning!

Risk of hand

injury. Safety

gloves must be

worn.

«
...
2
3
4
5
6
...
»

Содержание Exterior 1200 Wash





















































































Отзывы:

Нет отзывов