3-13
3-13
- Check the condition of the tyres, to detect cuts, pr
- Check the condition of the tyres, to detect cuts, pr
otuberances, wear, etc.
otuberances, wear, etc.
-
-
Check the torque load of the wheel nuts. Non compliance wit
Check the torque load of the wheel nuts. Non compliance wit
h this instruction can cause damage and rupture to the wheel bolts
h this instruction can cause damage and rupture to the wheel bolts
and distortion to the wheels.
and distortion to the wheels.
Wheel nuts tightening torque
Wheel nuts tightening torque
• Fron
• Fron
t tyres
t tyres
: 630
: 630
N.m
N.m
(465 lbf/ft)
(465 lbf/ft)
± 15%
± 15%
• Rea
• Rea
r tyre
r tyre
s: 630
s: 630
N.m
N.m
(465 lbf/ft)
(465 lbf/ft)
± 15%
± 15%
- Check and adjust the tyre pr
- Check and adjust the tyre pr
essures if necessary
essures if necessary
(see: 2 - DESCRIPTION: FRONT AND REAR TYRES).
(see: 2 - DESCRIPTION: FRONT AND REAR TYRES).
Check that the air hose is correctly connected to the tyre valve before inflating and keep all persons at a distance during inflation. Respect the
Check that the air hose is correctly connected to the tyre valve before inflating and keep all persons at a distance during inflation. Respect the
recommended tyre pressures given.
recommended tyre pressures given.
NOTE: There is an OPTIONAL wheel toolkit.
NOTE: There is an OPTIONAL wheel toolkit.
A6 - JIB PADS
A6 - JIB PADS
CLEAN - GREASE
CLEAN - GREASE
To be carried out every 10 hours during the first 50 hours service, then once at 250
To be carried out every 10 hours during the first 50 hours service, then once at 250
hours.
hours.
- Extend the
- Extend the
jib completely.
jib completely.
-
-
With a brush, apply a coat
With a brush, apply a coat
of grease (see: 3 - MAINTENANCE: LUBRIC
of grease (see: 3 - MAINTENANCE: LUBRIC
ANTS AND F
ANTS AND F
UEL) on
UEL) on
the 4 sides of the telescope(s) (fig. A6).
the 4 sides of the telescope(s) (fig. A6).
-
-
Tel
Tel
escope the jib several times in order to spread the coat of grease evenly
escope the jib several times in order to spread the coat of grease evenly
.
.
- Remove the surplus of grease.
- Remove the surplus of grease.
If the lift truck is
If the lift truck is
used in an abrasive environment (dust, sand, coal…) Use lubricating varnish (MANITOU
used in an abrasive environment (dust, sand, coal…) Use lubricating varnish (MANITOU
reference: 483536). In this r
reference: 483536). In this r
espect, consult your dealer.
espect, consult your dealer.
A6
A6
https://www.forkliftpdfmanuals.com/
Содержание MLT625-75 H S1-E3
