Manitou MLT625-75 H S1-E3, Руководство оператора

Страница: 113 / 160

3-2 3-2 7 7
NOTE: After an accident, replace the seat belt. NOTE: After an accident, replace the seat belt.
In no event should the lift In no event should the lift truck be used if the seat belt truck be used if the seat belt is defective (fixing, locking, cuts, tears, etc.). Repair or replace the seat belt immediately. is defective (fixing, locking, cuts, tears, etc.). Repair or replace the seat belt immediately.
E6 - REAR AXLE DIFFERENTIAL OIL E6 - REAR AXLE DIFFERENTIAL OIL
DRAIN DRAIN
Place the lift truck on level ground Place the lift truck on level ground with the I.C. engine stopped and the d oil still warm. with the I.C. engine stopped and the d oil still warm.
Dispose of the drain Dispose of the drain oil in oil in an ecological manner. an ecological manner.
- Place a container under drain plug 1 (fig. E6) and unscrew - Place a container under drain plug 1 (fig. E6) and unscrew them. them.
- - Remove level and filli Remove level and filli ng plug 2 (fig. E6) to ensure that the oil is drained properly ng plug 2 (fig. E6) to ensure that the oil is drained properly . .
- - Refit and Refit and tighten drain pl tighten drain pl ug 1 (fig. ug 1 (fig. E6) (tightening E6) (tightening torque 34 to 49 torque 34 to 49 N.m). N.m).
- - Fill up with oil (see: 3 - MAINTENANC Fill up with oil (see: 3 - MAINTENANC E: LUBRICAN E: LUBRICAN TS AND FUEL) through filler port 2 (fig. E6). TS AND FUEL) through filler port 2 (fig. E6).
- The level is correct - The level is correct when the oil level is flush with the edge of the when the oil level is flush with the edge of the hole. hole.
- Check for any possible leaks at the drain plug. - Check for any possible leaks at the drain plug.
- - Refit and tighten level and fill Refit and tighten level and fill ing plug 2 (fig. E6) (tightening torque 34 to 4 ing plug 2 (fig. E6) (tightening torque 34 to 4 9 9 N.m) N.m) 25-36lbf/ft 25-36lbf/ft . .
E7 - FRONT AND REAR WHEELS REDUCERS OIL E7 - FRONT AND REAR WHEELS REDUCERS OIL
DRAIN DRAIN
Place the lift truck on level ground with the I.C. engine stopped and the reducers oil still Place the lift truck on level ground with the I.C. engine stopped and the reducers oil still
warm. warm.
Dispose of the drain Dispose of the drain oil in oil in an ecological manner. an ecological manner.
- Drain and change the oil of each - Drain and change the oil of each wheel reducer. wheel reducer.
- Place drain pl - Place drain pl ug 1 (fig. E7) ug 1 (fig. E7) in position in position A. A.
- Place a container under the drain plug and unscrew - Place a container under the drain plug and unscrew the plug. the plug.
- Let the - Let the oil drain fully. oil drain fully.
- Place the drain port in position B, i.e. in a level port. - Place the drain port in position B, i.e. in a level port.
- - Fill up with oil (see: 3 - MAINTENANC Fill up with oil (see: 3 - MAINTENANC E: LUBRICAN E: LUBRICAN TS AND FUEL) through level port 1 (fig. E7). TS AND FUEL) through level port 1 (fig. E7).
- The level is correct - The level is correct when the oil level is flush with the edge of the when the oil level is flush with the edge of the hole. hole.
- Refit and tight - Refit and tight en the drain plug (ti en the drain plug (ti ghtening torque 34 to 49 ghtening torque 34 to 49 N.m) N.m) 25-36-lbf/ft 25-36-lbf/ft . .
E7 E7
B B
A A
1 1
E6 E6
1 1
2 2
https://www.forkliftpdfmanuals.com/