Manitou MLT625-75 H S1-E3, Руководство оператора

Страница: 107 / 160

3-2 3-2 1 1
- Remove access panel 1 (fig. D1/1). - Remove access panel 1 (fig. D1/1).
- - Place a container under the drain plug and unscrew the drain pl Place a container under the drain plug and unscrew the drain pl ug 2 (fig. D1/2). ug 2 (fig. D1/2).
- Remove filler cap 3 (fig. D1/3) in order to ensure - Remove filler cap 3 (fig. D1/3) in order to ensure that the oil is drained properly. that the oil is drained properly.
Dispose of the drain oil in Dispose of the drain oil in an ecological manner an ecological manner . .
REPLACEMENT OF THE REPLACEMENT OF THE FIL FIL TER TER
- Unscrew and discard the I.C. engine oil filter 4 (fig. D1/2) as well as - Unscrew and discard the I.C. engine oil filter 4 (fig. D1/2) as well as its seal. its seal.
- Clean the filter bracket with a clean, lint-free cloth. - Clean the filter bracket with a clean, lint-free cloth.
- - Lightly grease the new seal before refitti Lightly grease the new seal before refitti ng the new oil filter (s ng the new oil filter (s ee: 3 - MAINTENANCE ee: 3 - MAINTENANCE : :
FILTERS AND BELTS) on its bracket. FILTERS AND BELTS) on its bracket.
Tighten the oil filter by hand pressure only and lock the filter in place by a quarter turn. Tighten the oil filter by hand pressure only and lock the filter in place by a quarter turn.
FILLING UP THE OIL FILLING UP THE OIL
- Refit and tighten drain plug 2 (fig. D1/2). - Refit and tighten drain plug 2 (fig. D1/2).
- - Fill up with oil (see: 3 - MAINTENA Fill up with oil (see: 3 - MAINTENA NCE: LUBRICANTS A NCE: LUBRICANTS A ND FUEL) through filler port 5 ND FUEL) through filler port 5
(fig. D1/3). (fig. D1/3).
- Wait a few minutes to allow the oil to flow into the sump. - Wait a few minutes to allow the oil to flow into the sump.
- Start the I.C. engine and let it run for a few minutes. - Start the I.C. engine and let it run for a few minutes.
- Check for possible leaks - Check for possible leaks from the drain plug from the drain plug and the oil filter. and the oil filter.
- - Stop the I.C. engine, wait a f Stop the I.C. engine, wait a f ew minutes and check the correct level on the dipsti ew minutes and check the correct level on the dipsti ck 6 ck 6
(fig. D1/3) between the two level marks. (fig. D1/3) between the two level marks.
- Top up the level if - Top up the level if necessary. necessary.
- Refit access panel 1 (fig. D1/1). - Refit access panel 1 (fig. D1/1).
D3 - DRY AIR FILTER CARTRIDGE D3 - DRY AIR FILTER CARTRIDGE
CHANGE CHANGE
In case of use in a heavily dust laden atmosphere, there are In case of use in a heavily dust laden atmosphere, there are pre-filtration cartridges, see: pre-filtration cartridges, see:
3 - MAINTENANCE: FILTERS CARTRIDGES AND BELTS. Also, the checking and cleaning 3 - MAINTENANCE: FILTERS CARTRIDGES AND BELTS. Also, the checking and cleaning
periodicity of the cartridge must be reduced (up to 250 hours in a heavily laden dust periodicity of the cartridge must be reduced (up to 250 hours in a heavily laden dust
atmosphere and with pre-filtration). atmosphere and with pre-filtration).
Change the cartridge in a clean location, with the I.C. engine stopped. Never operate the lift truck with Change the cartridge in a clean location, with the I.C. engine stopped. Never operate the lift truck with
the air filter removed or damaged. the air filter removed or damaged.
- Open the I.C. engine bonnet. - Open the I.C. engine bonnet.
- Loosen the bolts and remove cover 1 - Loosen the bolts and remove cover 1 (fig. D3). (fig. D3).
- - Gently remove the cartridge 2 (fig. D3), ta Gently remove the cartridge 2 (fig. D3), ta king care to avoid spill king care to avoid spill ing the dust. ing the dust.
- Leave the safety cartridge in place. - Leave the safety cartridge in place.
- - The following parts must be cleaned wi The following parts must be cleaned wi th a damp, clean th a damp, clean lint-free cloth. lint-free cloth.
• The inside of • The inside of the filter and cover. the filter and cover.
• The inside of the filter inlet hose. • The inside of the filter inlet hose.
• The gasket sur • The gasket sur faces in the filter and in the cover. faces in the filter and in the cover.
- - Check pipes and connections between the air filter and the I.C. engi Check pipes and connections between the air filter and the I.C. engi ne and the connection and state of the clogging indicator on ne and the connection and state of the clogging indicator on
the filter. the filter.
- - Before mounting check the condition of the new car Before mounting check the condition of the new car tridge (see: 3 - MAINTENANCE: FIL tridge (see: 3 - MAINTENANCE: FIL TERS CARTRIDGES AND BEL TERS CARTRIDGES AND BEL TS). TS).
- - Introduce the car Introduce the car tridge into the filter axis and push i tridge into the filter axis and push i t in, pressing the edges and not the middle. t in, pressing the edges and not the middle.
- Reassemble the cover, guiding the valve downwards. - Reassemble the cover, guiding the valve downwards.
D1/3 D1/3
5 5
6 6
3 3
D3 D3
1 1
2 2
D1/2 D1/2
2 2
4 4
D4 - FUEL FILTER D4 - FUEL FILTER
CHANGE CHANGE
- Open the I.C. engine bonnet. - Open the I.C. engine bonnet.
- - Carefully clean the outside of the fi Carefully clean the outside of the fi lter and its holder lter and its holder , to prevent dust from getting into , to prevent dust from getting into
the system. the system.
- - Unscrew filter 1 (fi Unscrew filter 1 (fi g. D4) and discard it g. D4) and discard it after having recovered part 2 (fig. D4). after having recovered part 2 (fig. D4).
- - Refit the assembly with a new filter (see: 3 - MAINTENA Refit the assembly with a new filter (see: 3 - MAINTENA NCE: FIL NCE: FIL TERS CARTRIDGES A TERS CARTRIDGES A ND ND
BELTS). BELTS).
- - Pressurise the circuit Pressurise the circuit by means of the by means of the hand pump 3 (fig. hand pump 3 (fig. D4). D4).
D5 - HYDRAULIC D5 - HYDRAULIC RETURN OIL FILTER CARTRIDGE RETURN OIL FILTER CARTRIDGE
CHANGE CHANGE
D4 D4
2 2
1 1
3 3
D5/1 D5/1
https://www.forkliftpdfmanuals.com/