Manitou MI 50L D ST3B S2 Скачать руководство пользователя страница 93

Страница: 93 / 112

FILLING WITH OIL

- Fill up with oil (

LUBRICANTS AND FUEL) through filler port 8.

- NOTE: For this operation, we recommend you use a funnel fitted with a hose.

- Wait a few minutes to allow the oil to flow into the sump.

- Reinsert dipstick 4 and remove it again.

- Check the correct level between the two marks on the dipstick.

- Start the engine and let it run for a few minutes.

- Check for possible leaks.

- Stop the engine, wait a few minutes and check the level between the two marks.

- Top up the level if necessary.

MI . . D ST3B S2

DRAINING THE OIL

- Remove gauge 1 to ensure proper emptying.

- Place a container under drain plug (2) and unscrew the plug.

REPLACING THE OIL FILTER

- Unscrew and discard the filter 3, together with its seal.

- Lubricate the seal of the new filter (

FILTER CARTRIDGES AND BELTS).

- Refit the new filter onto its support bracket, hand-tighten it only and lock it with

a quarter-turn.

CLEANING THE METAL OIL FILTER

- Unscrew the filter 4.

- Clean the filter with a compressed air jet.

- Refit the unit.

FILLING WITH OIL

- Fill up with oil (

LUBRICANTS AND FUEL) through filler port 5.

- Wait a few minutes to allow the oil to flow into the sump.

- Reinsert dipstick 1 and remove it again.

- Check the correct level between the two marks on the dipstick.

- Start the engine and let it run for a few minutes.

- Check for possible leaks.

- Stop the engine, wait a few minutes and check the level on the dipstick.

- Top up the level if necessary.

3 - 31

647650 (19/02/2018) MI-X 50L/60/70 D C ST3A S2 / MI 50L/60/70 D ST3B S2 / MI 50L/60/70 G S2

Содержание MI 50L D ST3B S2

















































































































Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды

Manitou MI 50L D ST3B S2, Руководство оператора

Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды