Manitou MI 50L D ST3B S2 Скачать руководство пользователя страница 86

Страница: 86 / 112

Ân

500H - PERIODIC MAINTENANCE - EVERY 500 HOURS OF SERVICE

GREASE

Mast lifting chains

- Wipe the mast lifting chains with a clean, lint-free cloth.

- Vigorously brush the chains to get rid of any foreign matter, with a hard nylon

brush and clean diesel fuel.

- Rinse the chains by means of a paint brush impregnated with clean diesel fuel and

dry them with a compressed air jet.

- Carefully check each chain for any signs of wear.

IMPORTANT

In case of technical faults, consult your dealer.

- Grease the chains sparingly (

LUBRICANTS AND FUEL).

REPLACE

Engine oil

REPLACE

Engine oil filter

IMPORTANT

Dispose of the drain oil in an ecological manner.

- Place the lift truck on level ground, let the engine run at idle for a few minutes, then stop the engine.

MI-X . . D C ST3A S2

- Open the engine cover (

DESCRIPTION: INSTRUMENTS AND CONTROLS).

- Unscrew the thumbscrews 1 and remove the housing 2.

- Remove the cover 3 to access filler cap 4.

- Clean the areas around the plugs and oil filter.

DRAINING THE OIL

- Remove the filler plug 4 to ensure that the oil is drained properly.

- Place a container under drain port 5 and unscrew the plug.

REPLACING THE ENGINE OIL FILTER

- Unscrew and discard the filter 6, together with its seal.

- Clean the filter holder with a clean, lint-free cloth.

- Lightly grease the seal before refitting the new filter (

FILTER CARTRIDGES AND

BELTS) on its bracket.

- Tighten the oil filter (tightening torque 15 to 17 N.m).

FILLING WITH OIL

- Refit and tighten the drain plug 5 (tightening torque 30 to 40 N.m).

- Fill up with oil (

LUBRICANTS AND FUEL) through filler port 4.

NOTE: For this operation, we recommend you use a funnel fitted with a hose.

- Wait a few minutes to allow the oil to flow into the sump.

- Start the engine and let it run for a few minutes.

- Check for possible leaks from the drain plug and the oil filter.

- Stop the engine; wait a few minutes

- Check the correct level between the two notches on dipstick 7.

- Top up the level if necessary.

3 - 24

647650 (19/02/2018) MI-X 50L/60/70 D C ST3A S2 / MI 50L/60/70 D ST3B S2 / MI 50L/60/70 G S2

Содержание MI 50L D ST3B S2

















































































































Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды

Manitou MI 50L D ST3B S2, Руководство оператора

Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды