Manitou MI 50L D ST3B S2 Скачать руководство пользователя страница 90

Страница: 90 / 112

Âo

1000H - PERIODIC MAINTENANCE - EVERY 1000 HOURS OF SERVICE OR 2 YEARS

ALSO PERFORM THE 500 HOUR PERIODIC MAINTENANCE OPERATIONS.

CHECK

Safety belt

IMPORTANT

If the seat belt is defective (fixing, locking, cuts, tears, etc.), the lift truck must not be used.

Repair or replace the seat belt immediately.

SEAT BELT WITH TWO ANCHORING POINTS

- Check the following points:

• Fixing of the anchoring points on the seat.
• Cleanness of the strap and the locking mechanism.
• Triggering of the locking mechanism.
• Condition of the strap (cuts, curled edges).

REELED SEAT BELT WITH TWO ANCHORING POINTS

- Check the points listed above together with the following points:

• The correct winding of the belt.
• Condition of the reel guards.
• Roller locking mechanism when the strap is given a sharp tug.

LUBRICATE

Service brake pedal axle

IMPORTANT

In the event of prolonged use in an extremely dusty or oxidizing atmosphere, reduce this interval to 500 hours of

service or every year.

In case of technical faults, consult your dealer.

- Remove the floor mat.

- Unscrew the screws 1.

- Remove the clips 2 in order to remove the casing 3.

- Clean, then lubricate the lubricator 4 located at the end of the brake pedal axle (

LUBRICANTS AND FUEL) and remove any excess grease.

3 - 28

647650 (19/02/2018) MI-X 50L/60/70 D C ST3A S2 / MI 50L/60/70 D ST3B S2 / MI 50L/60/70 G S2

Содержание MI 50L D ST3B S2

















































































































Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды

Manitou MI 50L D ST3B S2, Руководство оператора

Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды