Manitou MI 50L D ST3B S2 Скачать руководство пользователя страница 100

Страница: 100 / 112

OCCASIONAL MAINTENANCE

FRONT WHEEL

- Lift the carriage and tilt the mast backwards.

- Immobilise under the foot of the mast on the side where the wheel is being changed.

- Tilt the mast forwards to lift the wheel.

- Place wedges under the chassis as near as possible to the wheel.

- Completely unscrew the wheel nuts and remove them.

- Free the wheel by reciprocating movements and roll it to the side.

- Slip the new wheel on the wheel hub.

- Hand-tighten the nuts, grease them if necessary.

- Remove the wedges under the axle and lower the lift truck.

- Tighten the wheel nuts using a torque wrench for the tightening torque. (

2000 HOURS - PERIODIC MAINTENANCE)

REPLACE

Wheels

IMPORTANT

In the event of a wheel being changed on the public highway, secure the lift truck vicinity:

- Stop the lift truck, if possible on firm, level ground.

- Shut down the lift truck (

OPERATING INSTRUCTIONS UNLADEN AND LADEN).

- Switch on the warning lights (option).

- Immobilise the lift truck in both directions on the axle opposite to the wheel to be changed.

- Unlock the nuts of the wheel to be changed.

REAR WHEEL

For this operation, we advise you to use the hydraulic jack (MANITOU Part no. 505507).

- Place the jack under the counterweight. It must be situated in the middle and under

the flat part of the counterweight.

- Lift the wheel until it comes off the ground and put in place the safety block under

the axle.

- Completely unscrew the wheel nuts and remove them.

- Free the wheel by reciprocating movements and roll it to the side.

- Slip the new wheel on the wheel hub.

- Hand-tighten the nuts, grease them if necessary.

- Remove the security block and lower the lift truck with the jack.

- Tighten the wheel nuts using a torque wrench for the tightening torque. (

2000 HOURS - PERIODIC MAINTENANCE)

3 - 38

647650 (19/02/2018) MI-X 50L/60/70 D C ST3A S2 / MI 50L/60/70 D ST3B S2 / MI 50L/60/70 G S2

Содержание MI 50L D ST3B S2

















































































































Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды

Manitou MI 50L D ST3B S2, Руководство оператора

Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды