Manitou MI 50L D ST3B S2 Скачать руководство пользователя страница 81

Страница: 81 / 112

CHECK

Gear box seal

- Place the lift truck on level ground with the engine stopped.

- Open the engine cover (

DESCRIPTION: INSTRUMENTS AND CONTROLS).

- Visually check for seepage and leaks.

- If there are any, check the level.

MI-X . . D C ST3A S2
MI . . G S2

- Pull out and clean the dipstick 1.

- Reinsert the dipstick and remove it again.

- Check the correct level between the two notches.

- If necessary, add oil (

LUBRICANTS AND FUEL) through the same hole 2.

CHECK

Front axle differential seal

Place the lift truck on level ground with the engine stopped.

- Visually check for seepage and leaks.

- If there are any, check the level.

- Raise the mast to gain access to the plug.

- Remove the level plug 1, the oil should be flush with the edge of the opening.

- If necessary, add oil (

LUBRICANTS AND FUEL) through the filler port 2.

- Refit and tighten the plugs (tightening torque 34 to 49 N.m).

CHECK

Tyre pressures

CHECK

Wheel nut torques

IMPORTANT

Check that the air hose is correctly connected to the tyre valve before inflating and keep all persons at a distance during inflation.

Inflate to the recommended tyre pressures.

- Check the torque load of the wheel nuts. Non-compliance with this instruction can lead to damage and failure of the

wheel bolts and distortion of the wheels.

- Check and restore tyre pressures if necessary (

TYRES).

NOTE: There is an OPTIONAL wheel toolkit.

MI . . D ST3B S2

- Pull out and clean the dipstick 1.

- Reinsert the dipstick and remove it again.

- Check the correct level between the two notches.

- If necessary, add oil (

LUBRICANTS AND FUEL) through the same hole 2.

3 - 19

647650 (19/02/2018) MI-X 50L/60/70 D C ST3A S2 / MI 50L/60/70 D ST3B S2 / MI 50L/60/70 G S2

Содержание MI 50L D ST3B S2

















































































































Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды

Manitou MI 50L D ST3B S2, Руководство оператора

Результаты поиска

Содержание MI 50L D ST3B S2

Отзывы:

Похожие инструкции для MI 50L D ST3B S2

Бренды по названию

Популярные бренды