Manitou MI 50L D ST3B S2 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 112

background image

5 - DASHBOARD

Only for MI-X 50L D C ST3A S2

MI-X 60 D C ST3A S2
MI-X 70 D C ST3A S2

A - FUEL LEVEL

Zone A1 indicates that you are using the reserve supply and that
time of use is limited.

B - ENGINE WATER TEMPERATURE

• Zone B1 (0° to 50°) Use the lift truck with moderation,

wait for temperature to increase before
normal operation.

• Zone B2 (60° to 105°) Use lift truck normally.
• Zone B3 (110°) Use lift truck with moderation, monitor the temperature.
• Zone B4 (120°) Stop the lift truck, look for the cause of overheating.

C - HOUR METER

D - LEFT-HAND INDICATOR

E - RIGHT-HAND INDICATOR

As soon as the ignition key is in position I, indicator lamps

,

,

,

,

,

and

come on to indicate their proper

operation.

NOTE: If one of the red indicator lamps or the buzzer is not

working, carry out the necessary repairs.

As soon as the engine starts, indicator lamps

,

,

,

and

will go out.

Indicator lamps

and

will go out the moment their control is used.

BATTERY CHARGE

If this lamp comes on while the lift truck is in operation, switch off the engine immediately, seek the cause of the
electrical system fault and check the alternator belt. Consult your dealer if necessary.

ENGINE OIL PRESSURE

If this lamp comes on while the lift truck is in operation, switch off the engine immediately, seek the cause of the
engine fault and check the engine’s oil level. Consult your dealer if necessary.

PARKING BRAKE

This indicator lamp comes on when the parking brake is applied.

DIESEL ENGINE PREHEAT

Preheat is necessary. When the lift truck is switched on, the indicator lamp comes on for a few seconds and goes
off as soon as preheat is ended. Start the lift truck’s engine.

AIR FILTER CLOGGING

The light comes on when the air filter cartridge is clogged up. When this light remains continuously lit the cartridge
needs changing. Stop the lift truck and carry out the necessary repairs (

MAINTENANCE: SERVICING SCHEDULE).

TRANSMISSION OIL TEMPERATURE

If this lamp comes on while the lift truck is in operation, switch off the engine immediately, seek the cause of the
transmission fault and check the transmission oil level. Consult your dealer if necessary.

2-24

C

A

B

D

E

A1

B2

B4

B3

B1

647650 (19/02/2018) MI-X 50L/60/70 D C ST3A S2 / MI 50L/60/70 D ST3B S2 / MI 50L/60/70 G S2

«
...
46
47
48
49
50
...
»

Содержание MI 50L D ST3B S2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для MI 50L D ST3B S2

ECL Comfort 110

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: BRAVILOR BONAMAT Страницы: 76

DESKLINE DL15 IC

Бренд: Linak Страницы: 33

Бренд: MIDWEST FASTENERS Страницы: 2

Бренд: CAME Страницы: 28

PAC iEVO Series

Бренд: Stanley Страницы: 2

Бренд: ENTRYPASS Страницы: 27

Бренд: Ravaglioli Страницы: 102

Бренд: Chicago Electric Страницы: 2

THERMASGARD 9112

Бренд: S+S Regeltechnik Страницы: 48

Бренд: Radiant Страницы: 82

Бренд: Jasic Страницы: 18

SmartStuff SmartBox

Бренд: TCP Страницы: 2

Бренд: Chicago Electric Страницы: 2

Бренд: JETI model Страницы: 64

TWN4 MultiTech 3 BLE

Бренд: Elatec Страницы: 13

Бренд: GYS Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды