Man D 2848 LE 401 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 64

background image

Commissioning and operation

40

Pressing the “Syn./Trol.” key (press once) enables the “Trolling” function. Pres-
sing again (press once) disables the function once again.
It is only possible to enable or disable the trolling function on the active control
stand when the command master lever (both command master levers in the case
twin-engine systems) is (are) in the “Neutral” position. While the function is ac-
tive, LED L8 “Trolling” shows continuous light.
If there is a command change to another control stand, the active function “Trol-
ling” is also taken over onto the new control stand.

.

In the trolling mode, the command master function changes in comparison to
the power shift mode.

The command master function in the trolling mode is described below.

Gear: forwards

Clutch: 100% slip

(lock)

3

(lock)

Forwards area

1

2

Neutral

3

Operating field

Reverse area

2

Gear: reverse

Clutch: 100% slip

(lock)

Acoustic
signalling
device

Infinitely variable

slip adjustment and

speed increase

Infinitely variable

slip adjustment and

speed increase

Clutch: 0% slip (grip)

and max. speed

when trolling

Clutch: 0% slip (grip)

and max. speed

when trolling

To enable the trolling function, the command master must be in position

À

“Neutral”

(lock). The engine idles and the gearbox is in neutral.

If the trolling mode is enabled, the clutch is set to its highest slip level (100% slip). The
engine continues to idle and the gearbox is in neutral.

If the command master lever is set in position

Á

(lock), the gearbox is shifted into the

“Forwards or Reverse” position. The engine idles, but due to the greatest possible clutch
slip (100% slip) is not yet able to turn the propeller shaft, or can do so only very slowly.

If the command master lever is moved further towards position

Â

, the clutch slip drops

continuously and at the same time the engine speed rises.

SYN/TROL

«
...
36
37
38
39
40
...
»

Содержание D 2848 LE 401

































































Отзывы:

Нет отзывов

Похожие инструкции для D 2848 LE 401

Бренд: Nice Страницы: 23

Бренд: Avco Lycoming Страницы: 106

Бренд: Baldor Страницы: 1

Бренд: Superrollo Страницы: 68

Бренд: Raider Страницы: 193

Бренд: Fanotec Страницы: 2

Бренд: O.S. engine Страницы: 4

O.S. Max-160FXRing

Бренд: O.S. engine Страницы: 10

Бренд: O.S. engine Страницы: 11

Бренд: Continental Refrigerator Страницы: 348

Бренд: Wood-mizer Страницы: 192

Бренд: Asmo Marine Страницы: 8

Бренд: Iveco Страницы: 42

Бренд: ePropulsion Страницы: 44

Бренд: Iveco Страницы: 194

Бренд: Toyota Страницы: 185

Бренд: ZIEHL-ABEGG Страницы: 12

Бренд: ZIEHL-ABEGG Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды