Man D 2848 LE 401 Скачать руководство пользователя страница 29

Страница: 29 / 64

Commissioning and operation

Visual Quit / Test:

Standard function:

visual acknowledgement,

i.e. all flashing alarm texts in the currently visible alarm screen switch to

constant representation if the horn was acknowledged beforehand; the

red alarm LED integrated in the front plate is also switched from flashing

to continuous lighting. All other monitoring devices in the system are ac-

knowledged via the serial bus.

Test function if there is currently no alarm and / or all issued alarms have

been visually acknowledged beforehand:

Lamp test, i.e. the three LEDs

in the front plate are activated as long as the key is pressed.

Special function:

see explanation of key

-menu function:

Shift selection cursor to the right or increase input va-

lue.

RESET:

Standard function: The reset key can be used to reset a slow down or

stop alarm:

A reduction alarm can only be reset after reduction of the speed

below 800 rpm.

If the corresponding criteria have been met, horn and optics / test button

pressed / activated and the cause of the alarm eliminated, the reduction

or stop alarm in the central processing unit is reset.

Special function:

see explanation of key

−

-menu function:

Shift selection cursor to the left or decrease input value.

PAGE:

Standard function:

Switch to next highest display screen for analog en-

gine data. The page number is indicated in the top left-hand side of the

display with P1 to P4. Page 4 is followed again by page 1. If this key is

pressed while the alarm screen is on display, the monitor switches back

to the analog engine data from which the alarm screen was originally

called.

Special function:

Key enables setting of the LCD contrast with simulta-

neous pressing of the keys

T E S T

R E S ET

ALARMS:

Standard function:

Calling up the alarm screen; the five alarms or warn-

ings last issued and still present are displayed. At the top left of the moni-

tor is the code A1. If there are more than 5 messages issued, the mess-

ages can be displayed in groups of five by pressing the key again. The

page number is indicated in the top left with A1 to Ax. If the display jumps

to the 1st alarm screen or the display remains unchanged when the key

is pressed, no more messages are active.

Special function:

Holding the key for at least 5 seconds activates the

built-in configuration menu. There, the language, units, date and time

can be set.

Menu function:

Within the menu, this key has a cancel function (Esc).

The program moves back by one menu level and / or from the main

menu to the normal display function.

T E S T

P A G E

R E S ET

P A G E

ALARMS

M en

Содержание D 2848 LE 401

































































Результаты поиска

Содержание D 2848 LE 401

Отзывы:

Похожие инструкции для D 2848 LE 401

Бренды по названию

Популярные бренды

Man D 2848 LE 401, Руководство по эксплуатации

Результаты поиска

Содержание D 2848 LE 401

Отзывы:

Похожие инструкции для D 2848 LE 401

Бренды по названию

Популярные бренды