manualshive.com logo in svg

Man D 2848 LE 401, Руководство по эксплуатации

Поделиться
Скачать
Man D 2848 LE 401 Скачать руководство пользователя страница 10

Safety regulations

12

D

Exhaust gases are toxic. Comply with the instructions for the installation
of MAN Diesel engines which are to be operated in enclosed spaces.
Ensure that there is adequate ventilation and air extraction.

D

Keep vicinity of engine, ladders and stairways free of oil and grease. 
Accidents caused by slipping can have serious consequences.

During maintenance and care

D

Always carry out maintenance work when the engine is switched off. 
If the engine has to be maintained while it is running, e.g. changing the
elements of change-over filters, remember that there is a risk of scald-
ing. Do not get too close to rotating parts.

D

Change the oil when the engines is warm from operation.

Caution:

There is a risk of burns and scalding. Do not touch oil drain plugs or oil
filters with bare hands.

ËË

D

Take into account the amount of oil in the sump. Use a vessel of suffi-
cient size to ensure that the oil will not overflow.

D

Open the coolant circuit only when the engine has cooled down. 
If opening while the engine is still warm is unavoidable, comply with the
instructions in the chapter entitled “Maintenance and Care”.

D

Neither tighten up nor open pipes and hoses (lube oil circuit, coolant cir-
cuit and any additional hydraulic oil circuit) during the operation. 
The fluids which flow out can cause injury.

D

Fuel is inflammable. Do not smoke or use naked lights in its vicinity. The
tank must be filled only when the engine is switched off.

D

When using compressed air, e.g. for cleaning the radiator, wear goggles.

D

Keep service products (anti-freeze) only in containers which can not be
confused with drinks containers.

Содержание D 2848 LE 401

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды