manualshive.com logo in svg

Man D 2848 LE 401, Руководство по эксплуатации

Поделиться
Скачать
Man D 2848 LE 401 Скачать руководство пользователя страница 21

Commissioning and operation

23

Operation of the engine monitoring system BE1

The engine monitoring system BE1 warns

the ship operator if important engine oper-

ating values are outside the permissible

tolerance range.
The display unit of the engine monitoring

system (see picture) is installed in the

main navigating stand and, as an option,

in the secondary navigating stand (fly-

bridge) too. The alarm is raised:

D

acoustically by means of a horn

D

visually by the flashing of the respective

red check lamp (exception: in the event

of a fault in the electronic system the

respective check lamp is permanently

illuminated)

To protect the engine, the speed will be reduced if alarm warnings like engine oil pres-

sure, engine coolant temperature, charge-air temperature and coolant level) is raised.

The check lamp “reduced speed” is then illuminated permanently.

Note on engines with electronically controlled diesel injection (EDC):

After the ignition has been switched on, the lamp “Fault in the electronic system”
will come on momentarily (lamp check). If there is a fault in the electronically con-
trolled diesel injection system (EDC), the lamp “Fault in the electronic system” will
be illuminated permanently.

Operation of the engine monitoring system BE1 after an alarm has been triggered

The display unit has the following operating buttons:

Switching off of the alarm horn.

Switching off of the flashing signal of the respective check lamp, ie the flashing
light changes into permanent light. Before the flashing signal can be switched off,
the alarm horn must be switched off.

Lifting of the alarm message (the red check lamp will go out).
Precondition for lifting an alarm message:

D

Pressing of buttons “Horn off” and “Test” in the order indicated

D

Elimination of the cause of the alarm

Содержание D 2848 LE 401

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды