manualshive.com logo in svg

Man D 2848 LE 401, Руководство по эксплуатации

Поделиться
Скачать
Man D 2848 LE 401 Скачать руководство пользователя страница 41

Commissioning and operation

43

1st step: Command request on the selected control stand.

Execution:

−

Set the control lever of the command master in the takeover position 
(“Neutral” position or same travel direction as the command master that 
is in command).

−

Press “Command” key once to request the command on this control-
stand.

Consequence:

−

The acoustic signal transmitter “beeps” in short intervals.

−

The display “Command” flashes rapidly.

The command is now requested on this control stand. The control system has enabled
the command takeover and indicates this by means of short tone and lamp intervals.

.

If the control system issues long lamp and tone intervals, the subsequent command
takeover is refused. In this case, the control levers of the command master are usually
not in the correct position or there is a fault in the system.

2nd step: Command takeover on the selected control stand.

Execution:

−

Press “Command” key once to take over the command on this control 
stand.

Consequence:

−

The acoustic signal transmitter is silent.

−

The “Command” display shows continuous light.

The command takeover is complete and the command is now at this control stand.

Free command change (without lever comparison)

With this variant, a control stand change takes place without taking account of the lever
position of the command master involved in the command change. The command
change takes place in one step.

Command takeover on the selected control stand

Execution:

−

Press “Command” key (white) to take over the command on this con-
trol stand.

Consequence:

−

The “Command” display on the selected control stand immediately 

shows continuous 
light.

The command is immediately at this control stand and the control system 

instantly

 runs

the lever position of the command master set here.

In this variant, carelessness can lead to manoeuvres that are not intended.

Example: Lever of the active command master is in position “Full forwards”. 
Lever of the requesting command master is in the position “Full reverse”. If there were
a command change, a full reverse manoeuvre would be performed immediately.

Содержание D 2848 LE 401

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды