manualshive.com logo in svg

Malibu Boats 2009 21 vRide, Руководство пользователя

Поделиться
Скачать
Malibu Boats 2009 21 vRide Скачать руководство пользователя страница 74

2-44

Optional Equipment

Heater

If your boat is equipped with a heater, you will find an
ON/OFF accessory switch located on the dash panel. Located
at the base of the observer seat walkway is a snorkel tube that
can be pulled out and directed wherever you like within a 
five-foot radius. Please refer to the information provided in
your owner’s packet for specific use.

Figure 2-35. Heater

Boat Cover

If your boat is equipped with this option, know the 
type of coveryou are placing on your boat. Some
Boat Covers have been made strictly for mooring
and storage only, and some have been made for
storage and travel. If you question the type of cover
that you have purchased, check with your Malibu
dealer for assistance.

Figure 2-36. Boat Cover

Damage caused to your boat as a result of improper cover
use is not covered under your Malibu Boats warranty.
Damage can result from wind whipping, and possibly cause
abrasions to your gelcoat surface. Use the proper shipping
cover for travel purposes.

Stereo

The stereo head unit is located in the starboard side walk-through
panel (in the shifter panel above the shifter in Ride models). To
turn the stereo on, the dash ignition key switch must be turned on.
The key can be turned to the left if you will not be running the
boat. See Figure 2-36. Some systems, if equipped, will have an
optional remote pad located at the back of the boat either in the
passenger area, or exterior transom. For specific stereo use, please
refer to the stereo manual that was included in your owner’s
packet. Standard on all boats equipped with stereo system is an
MP3 input line. See instructions found in your owner’s packet for
specific use.

If your boat was equipped with optional sound equipment to
include CD changer, amplifier or subwoofer, please refer to these
specific manuals included in the owners’ packet for use.

Figure 2-37. Stereo 

Figure 2-38. Stereo 
Remote

 Chapter 2_09.qxd: Chapter 2 doc.qxd  10/7/08  3:11 PM  Page 44

Содержание 2009 21 vRide





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды