manualshive.com logo in svg

Malibu Boats 2009 21 vRide, Руководство пользователя

Поделиться
Скачать
Malibu Boats 2009 21 vRide Скачать руководство пользователя страница 17

1-1

Chapter 1

B

OATING

S

AFETY

At Malibu, safety is not an option!

General Precautions

Your Malibu boat has been constructed to meet all U.S. Coast Guard and National Marine
Manufacturers Association (NMMA) requirements. However, it is still your
responsibility as the boat owner to ensure the boat is always operated in a safe fashion.

U.S. Coast Guard regulations require certain safety equipment be present on your boat
during operation. Besides the U.S. Coast Guard regulations, other local and/or
international law enforcement agencies may have similar requirements. You should check
with your local marine enforcement agency regarding any such requirements before using
the waterways.

It is not intended for this manual to be a replacement for a course on boating safety. It is
highly recommended that if you are unfamiliar with the use and operation of a boat, you
seek advice and training from a qualified individual or organization. Check with your
local boating agency or Malibu dealer for more information about boating safety classes
in your area. 

Safety Statements

Throughout this manual, specific precautions and symbols identify safety related
information. Follow these precautions as indicated.

The Safety Alert symbol means Attention! Become Alert! Your Safety Is
Involved!

Indicates an imminently hazardous situation that, if not
avoided, will result in death or serious injury.

Indicates a potentially hazardous situation that, if not
avoided, could result in death or serious injury.

Indicates a potentially hazardous situation that, if not avoided,
could result in minor or moderate injury or property damage. It
may also be used to alert against unsafe practices.

Notice:

Indicates installation, operation or maintenance information
which is important but not hazard related.

1

 Chapter 1_09.qxd: Chapter 1 doc.qxd  10/7/08  3:05 PM  Page 1

Содержание 2009 21 vRide





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды