manualshive.com logo in svg

Malibu Boats 2009 21 vRide, Руководство пользователя

Поделиться
Скачать
Malibu Boats 2009 21 vRide Скачать руководство пользователя страница 50

2-20

MaliView RPM Cruise Screen

• Press “CRUISE” to enter cruise mode and to toggle between “SPEED” and “RPM”

cruise modes.

• The up and down arrows will change the set-point in both “SPEED” and “RPM”

cruise modes.

• Use the “ON/OFF/ENTER” button to turn the cruise on or off.
• Press “MUTE” to mute the JBL radio. (This function only works with the JBL radio.)
• Press “SAVE PRE-SET” to save or edit a pre-set. (See “Pre-Set” page.) This button

will also allow you to temporarily disable any alarm.

When the display prompts you with “RPM PULL UP,” the system will allow full throttle
control until a calculated speed has been reached.

After the calculated speed is reached, the system will automatically enter a “DECEL”
mode and slowly return the engine throttle to the set RPM.

When the system has engaged, the throttle bar will turn green. Keep the arrow in the gap
to allow the engine to hold the RPM.

NOTES:
• The gap appears when the engine has activated cruise and has control of the throttle.
• The RPM of the boat must be below the RPM set-point to turn on the cruise.
• The cruise will only hold RPM if the arrow is in the gap and is green.
• The cruise can be turned off at any time but will not disengage until the throttle has

returned below the gap.

100%

0%

RPM ENGAGED

100%

0%

RPM DECEL

100%

0%

RPM PULL UP

SETUP

PRE-SETS

GAUGES

MEDIA

ON / OFF
ENTER

2500

 750

RPM ACTUAL

RPM SET

RPM ON

100%

0%

STEREO      2

    FM1
    101.7

VOLT

TEMP

OIL

11.8 V

185 ºF

65 PSI

E

F

SA

VE

PRE-SET

MUTE

F

C

L

R MLS

RIDER

100

0%

CURRENT

STOW

A STEP BEYOND

CRUISE

 Chapter 2_09.qxd: Chapter 2 doc.qxd  10/7/08  3:10 PM  Page 20

Содержание 2009 21 vRide





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды