manualshive.com logo in svg

Malibu Boats 2009 21 vRide, Руководство пользователя

Поделиться
Скачать
Malibu Boats 2009 21 vRide Скачать руководство пользователя страница 66

2-36

Running the engine with the motor box open exposes
rotating machinery which can cause injury to occupants of
the boat.

Driver’s Seat

The driver’s seat can be adjusted forward and backward by
pulling the lever located on front left side of the driver’s
seat. Pull lever outward and adjust seat as needed.

Lumbar Support

The driver’s seat is equipped with a Lumbar Support. To
adjust, locate the twist knob located on the left side of the
seat bottom. Turn the knob clockwise to increase lean back
tension, or counterclockwise to decrease tension.

Swivel Seat Base

Some models are also equipped with a swivel seat
adjustment. To adjust the seat, release the lever directly
below the front center of the drivers seat area by lowering 
to the bottom of the seat base. Locate the twist knob on 
the left center of the seat base, (this knob is different than
the Lumbar Support) and turn counterclockwise to loosen. 
The seat should swivel freely. To reset the seat position,
simply reverse these steps.

Figure 2-20. Bolster Seat

Figure 2-21. Lumbar Adjuster

Figure 2-22. Seat Adjuster

 Chapter 2_09.qxd: Chapter 2 doc.qxd  10/7/08  3:10 PM  Page 36

Содержание 2009 21 vRide





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды