manualshive.com logo in svg

Malibu Boats 2009 21 vRide, Руководство пользователя

Поделиться
Скачать
Malibu Boats 2009 21 vRide Скачать руководство пользователя страница 23

1-7

Reporting

Boat operators are required by law to file a Boating Accident report with their state
boating law enforcement agency when their boat is involved in certain boating accidents.
A boating accident must be reported if there is a loss or probable loss of life, personal
injury requiring medical attention, damage exceeding $500, or there is a complete loss of
the boat. If any of these conditions arise, seek further assistance from local law
enforcement personnel.

Hazardous Conditions

Every waterway poses hazards that should be avoided. The following information
outlines some of the hazards which may be encountered. 

Weather

Learn and understand weather patterns
and signs of change. Bad weather can
cause an uncomfortable and unsafe
situation. If a storm approaches, seek a
safe harbor. 

Figure 1-3. Weather Hazards

Dam Spillways

The area around dam spillways is very hazardous and conditions can change rapidly. Stay
clear of the spillways and areas below dams.

Weeds

Weeds can generally be a threat to a boat’s engine and other components on the boat. If
weeds wrap around the propeller, they can create vibration in the engine. They also
restrict water intake, causing the engine to overheat. 

Shallow Water Operation

Shallow water brings on obvious hazards such as sand bars, stumps, rocks, etc. Know the
area you will be operating the boat in. Hitting objects at high speeds can cause severe
damage to people and the boat. If you know you will be navigating the boat in shallow
water, post a lookout and proceed slowly. 

Know the minimal depth your boat can safely travel.

   

 Chapter 1_09.qxd: Chapter 1 doc.qxd  10/7/08  3:06 PM  Page 7

Содержание 2009 21 vRide





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды