manualshive.com logo in svg

Malibu Boats 2009 21 vRide, Руководство пользователя

Поделиться
Скачать
Malibu Boats 2009 21 vRide Скачать руководство пользователя страница 56

2-26

Circuit Breakers

All major boat circuits are protected from shorting and overload by resettable circuit
breakers. If a problem develops with one of the following circuits, switch off the circuit
and wait about one minute. Then push the appropriate breaker button fully and switch on
the circuit. If the circuit continues to trip, there is a problem somewhere in the system.
See your dealership immediately to locate the problem.

Figure 2-13. Circuit Breaker Panels

Switches & Indicators

Accessory Switch Panels

These panels are located in the dash directly below the standard gauges and are used to
activate the following features. You will find the feature or accessory provided within
each button face for description.

•

Horn

•

Accessory Heater

•

Navigation Lights

•

Accessory Malibu Launch System (MLS)

•

Interior Lights

•

Accessory Stereo

•

Accessory Docking Lights

•

Bilge Pump

•

Accessory Tower Lights

•

Blower

•

Accessory Shower

 Chapter 2_09.qxd: Chapter 2 doc.qxd  10/7/08  3:10 PM  Page 26

Содержание 2009 21 vRide





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды