manualshive.com logo in svg

MAINLINE Kleiss MCS7-2PVC, Системное руководство

Поделиться
Скачать
MAINLINE Kleiss MCS7-2PVC Скачать руководство пользователя страница 17

16

Kleiss MCS7-2PVC System Manual   

|

www.MainlineControlSystems.com

The tapping procedure is finished when the 

drilling rod can rotate without any resistance.

NOTE: You will feel less resistance twice - once 

in the beginning when the pilot drill has perforated 

the pipe wall and secondly when the cutter is 

completely through.

WARNING: Always control the drilling rod.

Unlock the drilling rod by operating the orange 

tapping device lock. Then pull the drilling rod 

completely upwards above the slide gate valve.

(If assistance to get the cutter out is needed, turn 

the drilling rod clockwise.)

(NEVER turn the drilling rod counterclockwise. 

This can damage the cutter.)

(Be aware of the fact that the pressure inside 

the pipeline may automatically move the rod 

upwards. Avoid being above the rod with your 

hands or face.)

WARNING: Always control the drilling rod.

Close the slide gate valve.

Release pressure from the dome by opening bleed 

valve.

Содержание Kleiss MCS7-2PVC









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды