Magnetrol Eclipse 706GWR Скачать руководство пользователя | Manualshive

Страница: 97 / 108

background image

97

57-606 ECLIPSE Model 706 Guided Wave Radar Transmitter

4.0 Advanced Configuration/

Troubleshooting Techniques

This section contains information regarding some of the
advanced configuration and troubleshooting capability con-
tained within the Model 706 transmitter. These diagnostic
options are best suited for use with PACTware and the
Model 706 DTM, and should be implemented only after
contacting MAGNETROL Technical Support.

4.1

End-of-Probe Analysis (EOPA)

Note that due to the operation of this method, End of
Probe Analysis cannot be applied with interface measure-
ment, applications with a "water" bottoms, or with stratify-
ing liquids. Therefore, EOPA will not be available when
Measurement Type = Interface & Level.

When EOPA is enabled and the calculated (inferred level) is
being used, a diagnostic warning shown as "Inferred Level”
will be present.

4.1.1 Enable EOPA using PACT

ware

Click on the Device Setup tab, and then select Advanced
Config. In the lower left corner select the correct Polarity
for the End of Probe pulse, then turn on the EoP Analysis.
The Eop Dielectric box will then appear. Fill in the correct
Dielectric of the process medium being measured.

«
...
95
96
97
98
99
...
»

Содержание Eclipse 706GWR













































































































Отзывы:

Нет отзывов

Похожие инструкции для Eclipse 706GWR

Бренд: Manaras Opera Страницы: 4

Бренд: Harris Страницы: 162

Бренд: M-system Страницы: 3

Бренд: T.E.M. Страницы: 131

Бренд: M-system Страницы: 3

Бренд: ADTRAN Страницы: 17

Бренд: Aerospace Logic Страницы: 2

THERMASGARD ALTM1

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Retekess Страницы: 2

Бренд: Continental Refrigerator Страницы: 12

Бренд: AUDIOropa Страницы: 88

Бренд: Itm Страницы: 50

PowerTalk Head w/ADSP & SNS 04-22

Бренд: SGC Страницы: 72

Бренд: WAREMA Страницы: 6

Бренд: Procare Страницы: 2

Бренд: Icom Страницы: 20

Бренд: Icom Страницы: 227

Бренд: Icom Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды