Magnescale MG80-SC1 Скачать руководство пользователя страница 45

Страница: 45 / 51

8.4

Operation Commands

Command

Description

P-P

Command format

Switch to the peak-to-peak value mode.

①②

P-P

MAX

Command format

Switch to the maximum value mode.

①②

MAX

MIN

Command format

Switch to the minimum value mode.

①②

MIN

REAL

Command format

Switch to the current value mode.

①②

REAL

RCL

Command format

Recall preset value.

①②

RCL

MODE= / MODE=?

Refer to the setup commands.

When executed as an operation command, it is not recorded in ROM.

P= / P=?

Refer to the setup commands.

When executed as an operation command, it is not recorded in ROM.

CH= / CH=?

CL= / CL=?

Refer to the setup commands.

When executed as an operation command, it is not recorded in ROM.

RES

Command format

Reset (zero reset/reference point setting cancel).

①②

RES

START

Command format

Start (peak value reset).

①②

START

PAU

Command format

Pause (peak value update stop).

①②

PAU

③

= ON: Peak value update stop

OFF: Peak value update stop cancel

LCH

Command format

Latch (set the current value data latching).

①②

LCH

③

= ON: Current value output data latch stop

OFF: Current value output data latch stop cancel

Command format

Load reference point

①②

Command format

Read the data of all the channels.

Command format

Read the data of specific channels.

①②

Содержание MG80-SC1




















































Результаты поиска

Содержание MG80-SC1

Отзывы:

Magnescale MG80-SC1, Руководство по эксплуатации, Страница: 45 / 51

Результаты поиска

Содержание MG80-SC1

Отзывы: