Magnescale MG80-SC1 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 51

Magnescale MG80-SC1 Скачать руководство пользователя страница 28

27

/

48

7.4

Using the Setting Application to Configure the Settings

7.4.1

Download the Setting Application

1. Visit the Magnescale website

at

www.magnescale.com

and select the following:

Products

→ Digital Gauge

→ MG80-SC MG80-CM

→ Software

Download the setting application from “Setting application for Windows PC."

2. Save the file to the desired location on the PC and extract it with decompression software.

7.4.2

Connect

1. Prepare the “Setting application for Windows PC.”

Place the downloaded "MG80-SC_SettingTool.exe" file in the desired location.

2. Set the IP address on the PC where “Setting application for Windows PC" is installed.

Set the IP address of the PC so that it is on the same network as the IP address of the MG80-SC.

Example: MG80-SC with IP address 192.168.0.100 and subnet 255.255.255.0

IP address : 192.168.0.xxx *

Subnet mask : 255.255.255.0

* Do not set xxx to the same address as another connected device.

3. Establish the connection as shown below.

LAN cable
CAT5e

«
...
26
27
28
29
30
...
»

Содержание MG80-SC1




















































Отзывы:

Нет отзывов