.
5
CHAPTER 1: Specifications
1 Specifications
Video & Aux Signals:
Signal configuration………………………4 , individually routable channels per RJ-45 jack.
Input impedance.....................................100
Ω
balanced (Compatible with all MultiView equipment)
Nominal input amplitude.........................1 Volt P-P
Dynamic headroom ................................>3dB
Gain from transmitter input to receiver
output through switch ...…………………Unity
Coupling from transmitter input to
receiver output....…………………………DC
Circuitry bandwidth .................................>220MHz
Signal type ..............................................1,2,3,4 & 5 component video + aux channels (Via MultiView components)
Input connectors (UTP)............................RJ-45 Female
Input connectors (VGA)...........................HD15 female, 1/8” audio socket
Loop out connectors.........................…....RJ-45 Female
Output connectors…………………………RJ-45 female
Audio:
Audio signals are ported into the Mondo III Matrix via MutiView components or via a 3.5mm stereo audio jack for Mondo Direct.
The type of transmitters and receivers used therefore defines audio specifications. Please refer to the spec sheets for those
components.
RS 232 Serial:
Serial signals are ported into the Mondo III Matrix via MultiView components or via a 3.5mm audio jack for simplex transmit in a
Mondo Direct. Transmission is uni-directional broadcast in this mode.
Mondo III SAP versions allow bi-directional serial sessions with individual receivers. There are 8 DB9 COM ports on each Mondo
III SAP frame That can be used in conjunction with SAP enabled receivers for full bi-directional RS232 communication with the
device attached to the receiver. Reference Section 6 for SAP usage.
Control:
Protocol to switch…………………………RS-232/RS-422*, Selectable; 9600 baud standard,
(rate selectable to 9600, 19,200, 38,400, 57,600, 115,200)
8 data bits, 1 stop bit, no parity, no flow control.
Interface connector, input………….….….DB9 or 7 position Phoenix**
Interface connector, input………….….….USB mini B type (Mondo III SAP ONLY. Requires driver file: MONDO3_USB.inf)
Interface connector,
Interframe communication, input/output………...3 position Phoenix or 7 position Phoenix (used for Mondo Legacy mode only)***
All input to output switching commands are received and processed by the master frame. Additional frames used within the matrix
are connected in a daisy chain and receive processed commands from the master frame.
In Mondo III serial control mode, the BUS terminator switch must be ON for the first and last frames.
* The 7 pin phoenix serial input supports both RS-232 and RS-422 modes
The DB9 serial ports support RS-232 only
** When using Mondo III frames in a legacy Mondo system only the 7 pin phoenix serial connections are used.
*** The BUS connector and DB9 ports are disabled in this mode.
Power:
Power input .............................................100-240V / 50~60Hz
Fused input. Replace fuse with same rating: 250V, 2.5A, Slow Blow, 5x20mm
Consumption……………………………….200 W Max
Redundancy………………………………..2 independent fully redundant AC Mains inputs.
Environmental:
Temperature/humidity
Storage ………………………………...….-40° to +158°F (-40° to +70°C) / 10% to 90%, non-condensing
Operating...........................………………...0° to +104°F (0° to +40°C) / 10% to 90%, non-condensing
Mechanical:
Rack mount ................................……..…Standard, 4U 19” EIA
Enclosure type ..........................…………Front Panel: Powder coat over aluminum
Enclosure: Aluminum
Enclosure dimensions ......………………..7.0" H x 19" W x 10.25" D (178 mm H x 483 mm W x 260 mm D)
Weight ................................…….………..16.6 lbs (7.5 kg) fully populated (shipping weight: 24 lbs (10.9 kg))
Compliances .............................…………CE, NRTL Listed, FCC Part 15
MTBF ......................................……….….100,000 hours
3
Содержание Mondo III Matrix
Страница 1: ...1 Mondo III Matrix Installation Setup Guide...
Страница 43: ...43 41 NOTES...
