LXE 8650 Скачать руководство пользователя страница 108

Страница: 108 / 308

SE955 Laser Barcodes

Bluetooth Ring Scanner Guide

E-SW-BLUESCANPG-A

Transmit “No Read / Decode” Message

Parameter Default Value:

Disable

Use this parameter to decide whether a message is sent to the host when a barcode symbol does
not decode.

When enabled, and a symbol does not decode within either:

•

A trigger pull activates the laser and decode processing, the processing continues until a
trigger release, or

•

The laser decode processing continues until the Laser On Timeout is reached.

A “NR” (No Read) is transmitted to the host. Any prefix or suffixes which have been enabled are
appended around this message.

When disabled, and a symbol does not decode, no message is sent to the host.

Select an option by scanning either of the barcodes shown below. If you wish to change your
selection, scan Cancel.

Enable No Read

Disable No Read

Cancel

Содержание 8650





















































































































































































































































































































Результаты поиска

Содержание 8650

Отзывы:

Похожие инструкции для 8650

Бренды по названию

Популярные бренды

LXE 8650, Руководство пользователя

Результаты поиска

Содержание 8650

Отзывы:

Похожие инструкции для 8650

Бренды по названию

Популярные бренды