LXE 8650 Скачать руководство пользователя страница 71

Страница: 71 / 308

E-SW-BLUESCANPG-A

Bluetooth Ring Scanner Guide

Chapter 3 SE955 Laser Barcodes

This chapter’s explanations and instructions are directed toward

Symbol SE955 laser

scanner engines in Bluetooth Ring Scanners

. DO NOT SCAN THE BARCODES IN

THIS CHAPTER WITH ANY OTHER IMAGER / LASER ENGINE.

Introduction

Ring Scanner

To change a parameter value

Scan the appropriate barcode in this chapter. The new value
replaces the standard default value in memory.

The following barcode symbologies are supported:

Symbology

Default Setting

Chinese 2 of 5

Disabled

Codabar Disabled

Code 11

Disabled

Code 128

Enabled

Code 39

Enabled

Code 93

Disabled

Discrete 2 of 5

Disabled

Interleaved 2 of 5

Enabled

MSI Plessey

Disabled

GS1 DataBar (RSS)

Disabled

UPC/EAN
UPC-A
UPC-E
UPC-E1
EAN-8
EAN-13

Enabled
Enabled

Disabled

Enabled
Enabled

Figure 3-1 Supported SE955 Barcode Symbologies

The tethered ring scanner does not have beep / audio capability.

Содержание 8650





















































































































































































































































































































Результаты поиска

Содержание 8650

Отзывы:

LXE 8650, Руководство пользователя, Страница: 71 / 308

Результаты поиска

Содержание 8650

Отзывы: