LXE 8650 Скачать руководство пользователя страница 52

Страница: 52 / 308

Bluetooth Module Programming Barcodes

Bluetooth Ring Scanner Guide

E-SW-BLUESCANPG-A

Imager White LEDs

Parameter Default Value:

Disable

Note: This parameter applies only to the Ring Imager. If enabled, the value is ignored by the

Ring Scanner.

When Imager White LEDs is enabled, the LEDs inside the scan aperture illuminate at the same
time, and for the same amount of time, as the scan beam.

This parameter setting persists over a power cycle (remove and replace the module battery).

This parameter reverts to the default setting after a module Reset (holding the imager trigger for
30 seconds after reinstalling the module battery).

It reverts to the default setting after the Factory Defaults barcode is scanned.

When this Imager White LEDs parameter is not scanned but the

Decoding Illumination

parameter

Chapter 4 – SE4400 Imager Barcodes

is scanned, the Imager White LEDs setting reverts to

Disable after a power cycle.

The LEDs turn off when the scan beam turns off.

Disabling this parameter does not affect the scan beam or scan beam timer.

Note:

Enabling Imager White LEDs may reduce module battery life.

Scan the appropriate barcode below:

Enable Imager White
LEDs

Disable Imager
White LEDs

Содержание 8650





















































































































































































































































































































Результаты поиска

Содержание 8650

Отзывы:

LXE 8650, Руководство пользователя, Страница: 52 / 308

Результаты поиска

Содержание 8650

Отзывы: