manualshive.com logo in svg

Lucent Technologies DSP1611, Информационное руководство

Продукт "Lucent Technologies DSP1611" – это цифровой сигнальный процессор с высокой производительностью. Чтобы получить изделие "Lucent Technologies DSP1611" Information Manual, вы можете скачать руководство с сайта manualshive.com абсолютно бесплатно. В нем содержится важная информация о работе продукта.

Поделиться
Скачать
background image

DSP1611/17/18/27/28/29 DIGITAL SIGNAL PROCESSOR

Information Manual

Instruction Set

April 1998

4-18

DRAFT COPY  

Lucent Technologies Inc.

4.5 Instruction Set

(continued)

4.5.3 Data Move Instructions (continued)

Data Move Instruction Examples

Data move instructions must be written in the exact format shown. If the instructions are written in any other way 
(for example, R : Z instead of Z : R), the assembler produces an error message. All data move instructions can 
execute in the cache except for the long immediate (R = IM16).

R = IM16 loads the 16-bit immediate data value (IM16) into the specified destination register (R). This data move 
instruction cannot be executed in the cache.

SR = IM9 loads a 9-bit immediate data value (IM9) into one of the YAAU registers (j, k, rb, re, r0, r1, r2, or r3).
The 9 bits are loaded into the LSBs of the register. All registers are then zero-extended except for j and k which 
are sign-extended. This special-case immediate instruction is often referred to as a short immediate or register 
set instruction. Short immediate instructions require one word of program memory, execute in one cycle, and 
can be executed inside the cache. The DSP1600 Assembler defaults to the long immediate if the value IM9 is 
greater than 9 bits or if a label is used. The short immediate can be forced with the set mnemonic (if the value 
IM9 is greater than 9 bits, it is truncated to 9 bits). For example, set r0 = 0xf00d will load r0 with 0x00d.

R = Y loads the data contained in the specified Y source into the specified destination register (R).

R = aS[l] loads the data contained in bits 31—16 (or 15—0 if aSl is specified) of the specified accumulator (aS) 
into the specified destination register (R). If saturation on overflow is enabled (according to the SAT field of the 
auc register), the transferred accumulator value is limited (see 

Section 5.1, Data Arithmetic Unit

).

Y = R loads the data contained in the specified source register (R) into the specified Y destination.

aT[l] = R loads the data contained in the specified source register (R) into bits 31—16 (or 15—0 if aTl is speci-
fied) of the specified accumulator. If clearing of aTl is enabled (according to the CLR field of the auc register), 
then aTl is cleared (0) when the high half is loaded. The guard bits are loaded with the value of bit 31.

Z : R loads contents of memory location (Z) into a register (R), and stores old contents of register (R) into mem-
ory location (Z). (See 

Section 4.3.2, Compound Addressing

 for an explanation of this data transfer mode).

DR = *(OFFSET) loads from a direct address. Five bits in the instruction are concatenated with 11 bits in the 
ybase register to form a 16-bit address to Y memory. Data at that address is written to register DR.

*(OFFSET) = DR stores to a direct address. Data from register DR is written to the Y memory location specified 
by the direct address.

push(*rM) = R is an optional assembly-language form of the statement *rM++ = R and is used for stack 
operations. Data is written from register R to the memory location pointed to by the address in rM, and the 
address is incremented.

R = pop(*rM) is an optional assembly-language statement that creates two DSP instructions: *rM-- followed by 
R = *rM. This combination is used for stack operations. The pointer register rM is decremented, and data is writ-
ten from the new memory location to the register R. The decrement instruction is not interruptible, so interrupts 
cannot corrupt the two-instruction pop sequence.

Содержание DSP1611




























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSP1611

Acconeer A111 User Manual preview
A111
Бренд: Acconeer Страницы: 32
Paradyne 3172 Quick Reference preview
3172
Бренд: Paradyne Страницы: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Бренд: Paradyne Страницы: 2
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Бренд: Safety Vision Страницы: 40
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Бренд: Dahua Страницы: 452
Magma ExpressBox7 Quick Installation Manual preview
ExpressBox7
Бренд: Magma Страницы: 2
Cypress Semiconductor CY7C1350G Specification Sheet preview
CY7C1350G
Бренд: Cypress Semiconductor Страницы: 15
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Бренд: ZALMAN Страницы: 18
Procool SP480 Series Instructions preview
SP480 Series
Бренд: Procool Страницы: 2
Laser UDC CARD User Manual preview
UDC CARD
Бренд: Laser Страницы: 4
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Бренд: Oracle Страницы: 70
DTS XD10P Installation And Operation Manual preview
XD10P
Бренд: DTS Страницы: 94
ekwb 3831109819395 Manual preview
3831109819395
Бренд: ekwb Страницы: 10
LevelOne GSW-0508 User Manual preview
GSW-0508
Бренд: LevelOne Страницы: 10
SET 89299 Technical Description preview
89299
Бренд: SET Страницы: 38
3Com X5 Quick Start preview
X5
Бренд: 3Com Страницы: 2
3Com 3CRWE825075A Quick Start Manual preview
3CRWE825075A
Бренд: 3Com Страницы: 8
3Com AirProtect Enterprise Engine 6100 Quick Setup Manual preview
AirProtect Enterprise Engine 6100
Бренд: 3Com Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды