LS tractor R4041 Скачать руководство пользователя страница 118

Страница: 118 / 125

System

Faults

Possible causes

Solutions

When operating HST

pedal, tractor dose not

start.

▲

Low pressure relief set is too

low

▲

High pressure relief set is too

low

▲

HST charger valve fault

▲

Filter clogged

▲

Pump worn or part damaged

▲

HST moving part worn or

damaged

▲

Check and repair

▲

Check and repair

▲

Replace

▲

Replace filter

▲

Repair or replace

▲

Repair or replace after

check the circuit.

Tractor is still moving

▲

Neutral position of HST pedal

▲

Adjust neutral position

HST

Tractor is still moving

despite pedal being in

neutral position on

HST pedal.

is changed.

▲

HST pedal linkage damaged.

▲

HST arm bolt loosened.

▲

Replace damaged part

▲

Fasten the bolt with

adhesive

HST power is too low

▲

Oil shortage

▲

Air in HST circuit

▲

Transmission oil temperature

is too high.

▲

HST moving part worn

▲

HST filter clogged

▲

Add oil

▲

Check and repair the

hydraulic suction line.

▲

Stop engine to cool the oil,

and restart.

▲

Repair or replace

▲

Replace the filter

Abnormal noise

▲

Engine speed is too low.

▲

Oil temperature is too low.

▲

Set engine rpm over 1500

rev/min

▲

Run engine to warm up

the oil.

- 37

▲

Hydraulic oil filter clogged

▲

Oil shortage

▲

Replace the filter

▲

Add oil

Содержание R4041






























































































































Результаты поиска

Содержание R4041

Отзывы:

Похожие инструкции для R4041

Бренды по названию

Популярные бренды

LS tractor R4041, Руководство оператора

Результаты поиска

Содержание R4041

Отзывы:

Похожие инструкции для R4041

Бренды по названию

Популярные бренды