LS tractor R4041 Скачать руководство пользователя

Страница: 113 / 125

④

How to use jumper cables

※

if the battery which is attached to the tractor is discharged and needs to connect a auxiliary battery,

follow the instructions as below.

①

②

③

④

Engine

Normal

Discharge

Red cable

ⓐ

Connecting Jumper cables

Check followings before connecting the cables.

- is the spring of clamp normal?

- Is the cable and clamp cut-off?

1. Stop engine, apply parking brake and remove the

ignition key.

2. Connect two (+) terminals of both batteries.

with red cable.

(tractor battery-

①

, auxiliary battery-

②

)

ⓑ

Removing Jumper cables

Remove jumper cables as referring to the right

figure, “Removing order of jumper cables”.

③

④

Engine

Normal

Discharge

Red cable

Caution

▶

The gas generated from the battery can be exploded by spark.

▶

The negative(-) cable of auxiliary battery must be connected to the engine block,

not to the tractor battery.

▶

Keep all flames and sparks away and DO NOT smoke while you charge battery.

< Connecting order of jumper cables >

Black cable

(tractor battery-

①

, auxiliary battery-

②

)

3. Connect one end of black cable to (-) terminal(

③

)

of auxiliary battery and the other end to engine

block desired to start (

④

4. If engine does not start,

check the electrolyte level of each battery.

- 32

▶

Pay attention not to change the (+) and (-) pole. If not, it may cause a failure of

electric circuit or the damage of wire and even the polarity of battery can be

changed at over-discharged state.

Notice

< Removing order of jumper cables >

①

②

Normal

Discharge

Black cable

Содержание R4041






























































































































Результаты поиска

Содержание R4041

Отзывы:

Похожие инструкции для R4041

Бренды по названию

Популярные бренды

LS tractor R4041, Руководство оператора

Результаты поиска

Содержание R4041

Отзывы:

Похожие инструкции для R4041

Бренды по названию

Популярные бренды