LRX SCORPION страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 20

background image

LRX™ SCORPION

Check on line for the latest updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

15

15

`

Load must be centered front

to back as well as side to side

Using two truss plates (1/2” X 3”)

per side, a minimum of two

structural members must be

captured. Fasten using ½” X 4”

bolts with washers, lock washers

and nuts – four places

«
...
14
15
16
17
18
...
»

Содержание SCORPION





















Отзывы:

Нет отзывов

Похожие инструкции для SCORPION

Бренд: Camozzi Страницы: 2

Бренд: Landoll Страницы: 83

Бренд: R.M. Young Страницы: 10

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Jacobsen Страницы: 16

Бренд: Jacobsen Страницы: 20

Бренд: Jacobsen Страницы: 100

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: ParaBody Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды