LRX SCORPION страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 20

background image

LRX™ SCORPION

Check on line for the latest updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

13

13

LAMP INSTALLATION



A number of hazards exist during lamp installation please refer to

safety warnings on page two.



Follow lamp manufactures instructions regarding use and handling of their

product.



This fixture has more than one power supply. Disconnect all power supplies

before installation or removal of the lamps.



Allow lamps to cool before removing.



Loosen the two screws that hold the lamp retaining ring, then rotate ring to

remove.



Prior to installing the lamp, check lamp contacts and wire ends for signs of

arcing or over-heating. If lamp contacts or wiring appear damaged remove

from service.



Ensure power supply matches lamp type, voltage and wattage.

«
...
12
13
14
15
16
...
»

Содержание SCORPION





















Отзывы:

Нет отзывов

Похожие инструкции для SCORPION

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: EarthQuake Страницы: 12

Бренд: Pari Страницы: 2

Бренд: H&S Страницы: 42

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Бренд: DAAB Страницы: 12

Бренд: T&R Страницы: 26

The Huntington Raised Planter Bed

Бренд: Eden Страницы: 2

Бренд: Lightolier Страницы: 2

Bernardo 1320 S

Бренд: PWA Страницы: 12

Бренд: SPARTAN sport Страницы: 8

Бренд: hager Страницы: 2

Tone Works Pandora PX4D

Бренд: Korg Страницы: 196

1C61 Triton Vertical Shock

Бренд: Otto Bock Страницы: 248

Pro Power Rack RC20

Бренд: Tunturi Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды