LRX SCORPION страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 20

background image

LRX™ SCORPION

Check on line for the latest updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

12

12

Notice, to enable the fixture to fit into the shipping case:



Tilt fixture so that panel is vertical.



Pan fixture so that it is pointed straight ahead.



Install onto shipping frame, tighten hanger bolts and ratchet straps; ensure

there is a minimum of 1.5 wraps on the ratchet drum.



Secure gel frame holders using the Velcro straps provided in the shipping

trays.



Place hand controller into Pelican case and place in tray.



Hang DMX cables on shipping stand.



Always store equipment in a dry location.

Ensure 1.5 wraps

on ratchet drum

Hanger Bolt

«
...
11
12
13
14
15
...
»

Содержание SCORPION





















Отзывы:

Нет отзывов

Похожие инструкции для SCORPION

Бренд: Yardistry Страницы: 9

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: EuroLite Страницы: 28

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

Бренд: Land Pride Страницы: 36

Skid Steer Rakes SR2672

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 2

Disc Harrows DH3510

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 4

Бренд: Land Pride Страницы: 4

Straw Crimper CR2572

Бренд: Land Pride Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды