LOMBARDINI MARINE Kohler KDI 1903TCR-MP Скачать руководство пользователя страница 10

Страница: 10 / 56

_04

2.2

TECHNICAL INFORMATION

2.4 Oil

Important

•

The engine may be damaged if operated with improper oil

level.

•

Do not exceed the MAX level because a sudden increase in

engine rpm could be caused by its combustion.

•

Use only the recommended oil to ensure adequate protection,

efficiency and service life of the engine.

•

The use of lubricants other than recommended may shorten

the engine life.

•

Viscosity must be appropriate to the ambient temperature to

which the engine is to be exposed

(Par. 2.4.1)

Danger

•

Prolonged skin contact with the exhausted engine oil can

cause cancer of the skin.

•

If contact with oil cannot be avoided, thoroughly wash your

hands with soap and water as soon as possible.

•

For the exhausted oil disposal, refer to

Par. 6.8 DISPOSAL and SCRAPPING.

2.4.1

SAE oil classification

•

In the SAE classification, oils are identified according

to viscosity without considering any other qualitative

characteristic.

•

The code is made up of two numbers. The first number

refers to the viscosity when cold, for use during winter ("

winter), while the second number is for viscosity at high

temperatures.

2.4.2

Reversing gear oil

NOTE:

Refer to the technical documentation of the reversing gear supplied with the engine.

RECOMMENDED OIL

VISCOSITY

SAE

15W-40 (-15°C ÷ +50°C)

10W-30 (-25°C ÷ +40°C)
10W-40 (-25°C ÷ +50°C)

5W-30 (-30°C ÷ +40°C)
0W-40 (-40°C ÷ +50°C)

WITH

SPECIFICATIONS

API

CI-4 Plus

CI-4

CH-4

ACEA

E7
E5

• Filtration of oils is critical to proper operation and lubrication; always change filters regularly as specified in this manual.

ED0053032450

Содержание Kohler KDI 1903TCR-MP

























































Результаты поиска

Содержание Kohler KDI 1903TCR-MP

Отзывы:

Похожие инструкции для Kohler KDI 1903TCR-MP

Бренды по названию

Популярные бренды

LOMBARDINI MARINE Kohler KDI 1903TCR-MP, Руководство пользователя

Результаты поиска

Содержание Kohler KDI 1903TCR-MP

Отзывы:

Похожие инструкции для Kohler KDI 1903TCR-MP

Бренды по названию

Популярные бренды