LOMBARDINI MARINE Kohler KDI 1903TCR-MP Скачать руководство пользователя страница 33

Страница: 33 / 56

_04

5.12

INFORMATION ABOUT MAINTENANCE

5.13 Unused machine

If the machine is not used for a certain amount of time, follow the operations below:

5.13.1 Operations for the engine

POINT

OPERATION

unused ma-

chine up to 2

months

- The place must be dry and fresh throughout the period in which the machine is not used.

- Consult the machine’s manual to disconnect the battery (before disconnecting the battery,

wait for minimum 5 mins after turning off the engine).

- Make sure the engine is not exposed to direct sunlight.

- Make sure the engine is not near any heat sources.

Starting

- Before starting the engine, check

Par. 5.2

for maintenance operations.

- Consult the machine’s manual to connect the battery and start the engine.

unused machi-

ne from 2 to 9

months

- Perform the operations related to unused machine described in

point 1

- Perform the operations described in

Par.

5.6

- Start the engine at least every 4 months as per operations described in

point 1

Avoid sudden accelerations for the first few minutes.

Bring the engine to the working temperature by pressing the accelerator 3/4 from

MAX

Leave the engine running at minimum speed for a few minutes and turning off the engine.

Starting

- Before starting the engine, check

Par. 5.2

for maintenance operations.

- Consult the machine’s manual to connect the battery and start the engine.

Avoid sudden accelerations for the first few minutes.

unused ma-

chine over 9

months

- Perform the operations related to unused machine described in

point 1

and

Starting

- Before starting the engine, check

Par. 5.2

for maintenance operations.

- Check the quality of coolant from the relative testing strips.

- Consult the machine’s manual to connect the battery and start the engine.

Avoid sudden accelerations for the first few minutes.

ED0053032450

Содержание Kohler KDI 1903TCR-MP

























































Результаты поиска

Содержание Kohler KDI 1903TCR-MP

Отзывы:

Похожие инструкции для Kohler KDI 1903TCR-MP

Бренды по названию

Популярные бренды

LOMBARDINI MARINE Kohler KDI 1903TCR-MP, Руководство пользователя

Результаты поиска

Содержание Kohler KDI 1903TCR-MP

Отзывы:

Похожие инструкции для Kohler KDI 1903TCR-MP

Бренды по названию

Популярные бренды