LOMBARDINI MARINE Kohler KDI 1903TCR-MP Скачать руководство пользователя страница 19

Страница: 19 / 56

_04

4.9

INFORMATION ABOUT USE

• Read carefully the following pages and carry out the

operations described below in accordance with the
instructions specified.

4.1 Pre-start check

Important

• Non compliance with the operations described in the

following pages involves the risk of damages to the engine
and vehicle on which it is installed as well as personal and/
or property damage.

• Increase the frequency of maintenance operations in heavy

working conditions (engine starts but stops, very dusty and
hot environments, etc...).

4.2 Break-in running

NOTE:

For the first 50 hours of engine operation, it is advisable not to exceed 75% of the maximum power supplied.

4.3 Starting and turning off

4.3.1 Starting

Check the level of the engine oil, fuel and coolant and fill

if necessary (

Par. 4.5 and Par. 4.6

Put the ignition key in the ignition switch.

Tun the key to 1 position.

Press the Start push button for it to start automatically.

Important

• At the first fuelling or if the tank was empty filling the fuel

system (Par. 6.3 point 7).

• RPM reading delay is normal.
• If engine does not start after two attempts see

Tab. 7.1

and

Tab. 7.2

to found the cause.

4.3.2

After starting

Warning

• Make sure that all the warning lights on the control panel are off when the engine is running.
• Check for any leakages from the pipes on first start-up

Run at minimum speed for a few minutes according to table.

AMBIENT TEMPERATURE

TIME

≤ -20°C

2 minutes

from -20° C to -10°C

1 minutes

from -10° C to -5° C

30 seconds

from -5° C to 5° C

20 seconds

≥ 5° C

15 seconds

4.3.3

Turning off

Do not turn off the engine with a full load or when it is running at the maximum rotation speed. Leave it running at idle speed

without a load for approximately 1 minute.

Press the Stop push button (the engine turns off) and turn the key to position 0.

ED0053032450

Содержание Kohler KDI 1903TCR-MP

























































Результаты поиска

Содержание Kohler KDI 1903TCR-MP

Отзывы:

Похожие инструкции для Kohler KDI 1903TCR-MP

Бренды по названию

Популярные бренды

LOMBARDINI MARINE Kohler KDI 1903TCR-MP, Руководство пользователя

Результаты поиска

Содержание Kohler KDI 1903TCR-MP

Отзывы:

Похожие инструкции для Kohler KDI 1903TCR-MP

Бренды по названию

Популярные бренды