Linksys ATA Administration Guide
111
Regional page
Off Hook Warning Tone
Played when the caller has not properly placed the handset on the cradle. Off
Hook Warning Tone is played when Reorder Tone times out.
The default is
480@10,620@0;10(.125/.125/1+2)
.
Ring Back Tone
Played during an outbound call when the far end is ringing.
The default is
440@-19,480@-19;*(2/4/1+2)
.
Ring Back 2 Tone
Your ATA device plays this ringback tone instead of
Ring Back Tone
if the
called party replies with a SIP 182 response without SDP to its outbound
INVITE request. The default value is the same as
Ring Back Tone
, except the
cadence is 1s on and 1s off.
The default is
440@-19,480@-19;*(1/1/1+2)
.
Confirm Tone
Brief tone to notify the user that the last input value has been accepted.
The default is
600@-16; 1(.25/.25/1)
.
SIT1 Tone
Alternative to the Reorder Tone played when an error occurs as a caller
makes an outbound call. The RSC to trigger this tone is configurable on the
SIP
screen.
The default is
985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/
3,0/4/0)
.
SIT2 Tone
Alternative to the Reorder Tone played when an error occurs as a caller
makes an outbound call. The RSC to trigger this tone is configurable on the
SIP
screen.
The default is
914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/
3,0/4/0)
.
SIT3 Tone
Alternative to the Reorder Tone played when an error occurs as a caller
makes an outbound call. The RSC to trigger this tone is configurable on the
SIP
screen.
The default is
914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/
3,0/4/0
).
SIT4 Tone
Alternative to the Reorder Tone played when an error occurs as a caller
makes an outbound call. The RSC to trigger this tone is configurable on the
SIP
screen.
The default is
985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/
3,0/4/0)
.
MWI Dial Tone
Played instead of the Dial Tone when there are unheard messages in the
caller’s mailbox.
The default is
350@-19,440@-19;2(.1/.1/1+2);10(*/0/1+2)
.
Cfwd Dial Tone
Played when all calls are forwarded.
The default is
350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)
.
Holding Tone
Informs the local caller that the far end has placed the call on hold.
The default is
600@-19*(.1/.1/1,.1/.1/1,.1/9.5/1)
.
Conference Tone
Played to all parties when a three-way conference call is in progress.
The default is
350@-19;20(.1/.1/1,.1/9.7/1)
.
Secure Call Indication
Tone
Played when a call has been successfully switched to secure mode. It should
be played only for a short while (less than 30 seconds) and at a reduced level
(less than -19 dBm) so it does not interfere with the conversation.
The default is
397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)
.