Link electronics Caption Encoder/Decoder SD SDI/Analog PTC-892 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 38

background image

PTC-892 version 1 C

7

North American Power Supply Cords

This equipment is supplied with molded grounding plug (NEMA 5-15P) at
one end and molded grounding connector (IEC 320-C13) at the other end.
Conductors are CEE color coded, light blue (neutral), brown (line) and
green/yellow (ground).

Operation of this equipment at voltages exceeding 130 VAC will require
power supply cords which comply with NEMA configurations.

International Power Supply Cord

This equipment is supplied with molded grounding connector (IEC 320-
C13) at one end and stripped connectors (50/5 mm) at the other end.
Connectors are CEE color coded, light blue (neutral), brown (line) and
green/yellow (ground).

Other IEC 320-C13 type power supply cords can be used if they comply
with the safety regulations of the country in which they are installed.

Notes:

This equipment has been tested and found to comply with the limits for a
class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference, in which case the user will be required to
correct the interference at his own expense.

«
...
5
6
7
8
9
...
»

Содержание Caption Encoder/Decoder SD SDI/Analog PTC-892







































Отзывы:

Нет отзывов

Похожие инструкции для Caption Encoder/Decoder SD SDI/Analog PTC-892

Бренд: Panasonic Страницы: 12

Бренд: Accuphase Страницы: 26

Бренд: Datavideo Страницы: 18

Бренд: XINDAK Страницы: 9

Бренд: U.S. Converters Страницы: 19

Бренд: V-TAC Страницы: 4

Бренд: Whistler Страницы: 2

Бренд: Wacker Neuson Страницы: 22

Бренд: TTI Страницы: 7

Бренд: DAB PUMPS Страницы: 635

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

Бренд: National Semiconductor Страницы: 13

Бренд: D&R Страницы: 17

Бренд: TA Страницы: 32

Бренд: LC Страницы: 44

Бренд: CYP Страницы: 16

Бренд: MOOD Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды