Link electronics Caption Encoder/Decoder SD SDI/Analog PTC-892 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 38

background image

PTC-892 version 1 C

11

PTC-892 Rear Panel Connections (continued)

Communication Ports

Figure 10

Communication ports

: Green is Port 1, which is either RS-232 #1 or USB port,

and blue is Port 2, which is either RS-232 #2 or RJ-11.

Port 1 can be selected (RS-232 #1 or USB port) through the front panel. The

optional internal modem takes priority over the RS-232 #2 when connected. When the
modem is disconnected, the RS-232 #2 has control.

The PTC-892 has two nine pin subminiature “D” connectors on the rear panel for

RS-232 communications. The RJ-11 jack located on the rear panel allows the unit to
directly connect to a phone line when the optional internal modem is installed. The USB
“B”-plug can be plugged directly into a computer’s USB port and simulates a com port.

AC Power

Figure 11

AC power

: Green is the AC input, and blue is the fuse.

The PTC-892 accepts 110V-AC to 240V-AC. The fuse is a 5 x 20mm 750mA

buss fuse.

«
...
9
10
11
12
13
...
»

Содержание Caption Encoder/Decoder SD SDI/Analog PTC-892







































Отзывы:

Нет отзывов

Похожие инструкции для Caption Encoder/Decoder SD SDI/Analog PTC-892

Бренд: JED Страницы: 4

Бренд: D&H Страницы: 70

Бренд: Parker Страницы: 99

Бренд: 3onedata Страницы: 3

Allen-Bradley 842D

Бренд: Rockwell Automation Страницы: 58

Бренд: Agilent Technologies Страницы: 122

Бренд: Promate Страницы: 28

AS-07UR4SYDDB15

Бренд: Hisense Страницы: 59

Бренд: Walter Страницы: 216

SITE INVERTER 300

Бренд: ICT Страницы: 8

B+B SmartWorx 485USB9F-2W

Бренд: Advantech Страницы: 2

Бренд: DeLOCK Страницы: 2

Бренд: Niko Страницы: 8

Popcorn Hour A-410

Бренд: Syabas Technology Страницы: 95

AZZYRRO 3-6-ZSS-HP

Бренд: ZCS Страницы: 65

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology 8R

Бренд: M-Audio Страницы: 25

Бренд: GarrettCom Страницы: 60

Бренд: SAJ Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды