Lincoln 82206, Руководство владельца/оператора

Страница: 2 / 27

Page Number - 2
Form 404109
FAILURE TO HEED THE FOLLOWING WARNINGS INCLUDING MISUSE, OVER PRESSURIZING, MODIFYING PARTS,
USING INCOMPATIBLE CHEMICALS AND FLUIDS, OR USING WORN OR DAMAGED PARTS, MAY RESULT IN EQUIP-
MENT DAMAGE AND/OR SERIOUS PERSONAL INJURY, FIRE, EXPLOSION, OR PROPERTY DAMAGE.
·
Do not exceed the stated maximum working pressure of the reel or of the lowest rated component in your system.
·
Do not alter or modify any part of this equipment.
·
Do not operate this equipment with combustible gas.
·
Do not attempt to repair or disassemble the equipment while the system is pressurized.
·
Make sure all fluid connections are securely tightened before using this equipment.
·
Always read and follow the fluid manufacturer’s recommendations regarding fluid compatibility, and the use of protective
clothing and equipment.
·
Check all equipment regularly and repair or replace worn or damaged parts immediately.
·
Never point the dispensing valve at any part of the body or at another person.
·
Never try to stop or deflect material from dispensing valve or leading connection or component with your hand or body.
·
Always check equipment for proper operation before each use, making sure safety devices are in place and operat ing
properly.
·
Always follow the pressure relief procedure after shutting off the pump, when checking or servicing any part of the system,
and when installing cleaning or changing any part of the system.
ASSEMBLY
Assemble reel as follows. Refer to SERV ICE PARTS for part
numbers and location.
A. Assemble arbor and ratchet casting (237670) to sup-
port assembly (237656) with four hex head screws
(50014) and four hex nuts 51022).
B. Lubricate V-ring seal (237671) and place on arbor
and ratchet casting (237670) with lip facing away from
arbor ratchet.
C. Assemble power spring assembly (237672) onto
arbor and ratchet casting (237670) until spring
canister bottoms on arbors shoulder
D. Lubricate V-ring seal (237673) and assemble onto ar-
bor and ratchet casting (237670) with lip facing toward
spring canister.
E. Assemble axle (274835) to sheave assembly (237680)
with three nuts (51412).
F. Assemble axle and sheave assembly to reel by slid-
ing axle (274835) through bear ings in the arbor and
ratchet casting (237670). Secure with washer (48217)
and TRU-ARC (68424). Shim as required using shims
(48385) between washer (48217) and arbor and
ratchet casting (237670) to eliminate axle end play.
G. Rotate sheave assembly (237680) and align six
mounting holes with mating holes in power spring
cannister (237672). Secure with five carriage bolts
(237738). carriage bolt (237739) and six nuts (51412).
NOTE:The carriage bolt (237739) is assembled in
hole adjacent to pawl pin.
H. Assemble roller outlet arm assembly (237690) on
bolts (50014) and secure using three nuts (51022).
I. Assemble roller outlet as sembly (237692) to roller
outlet arm, assembly (237690) using (4) 50033 Hex
Head Screws and (4) 51304 Lock Nuts.
J. Assemble swivel assembly (274840) in axle (274835)
and tighten.
K. Assemble adapter assembly (273065) into swivel
assem bly (274840) and secure with U-keeper
(15674).
L. Assemble outlet adapter (273212) into axle (274835).
Secure with U-keeper (15674).
M. Assemble hose clamp to sheave assembly (237680)
with carriage bolt (237738). Secure with nut (51412).
N. Assemble latch pawl (237683) to pawl pin on power
spring assembly (237672) and secure with washer
(48327) and TRU- ARC (66316).
O. Assemble extension spring (237695) to latch pawl
(237683) and carriage bolt (237739). Secure with
locknut (51304).