Lincoln 2006 Town Car Скачать руководство пользователя страница 17

Страница: 17 / 45

Measure the resistance between EATC module C228a-10, circuit 660 (YE/LG) and
the recirc door actuator C289-1, circuit 660 (YE/LG).

Is the resistance less than 5 ohms?

GO to

REPAIR circuit 660 (YE/LG) for an open. CLEAR the DTCs. REPEAT the self-test.
TEST the system for normal operation.

E8 CHECK CIRCUIT 1069 (OG/LB) FOR AN OPEN

Measure the resistance between EATC module C228a-9, circuit 1069 (OG/LB) and
the recirc door actuator C289-6, circuit 1069 (OG/LB).

Is the resistance less than 5 ohms?

Yes

INSPECT for binding or broken linkage. If no condition is found, INSTALL a new door
actuator. REFER to

Section 412-01

. CLEAR the DTCs. REPEAT the self-test. TEST

the system for normal operation.

REPAIR circuit 1069 (OG/LB) for an open. CLEAR the DTCs. REPEAT the self-test.
TEST the system for normal operation.

E9 CHECK THE FEEDBACK POTENTIOMETER TOTAL RESISTANCE

Connect: Recirc Door Actuator C289.

Disconnect: Temperature Blend Door Actuator C2091.

Disconnect: Temperature Blend Door Actuator C2092.

Disconnect: Panel/Defrost Door Actuator C2248.

Disconnect: Floor Door Actuator C234.

Measure the resistance between EATC module C228b-8, circuit 436 (RD/LG) and
EATC module C228a-20, circuit 438 (RD/WH).

Is the resistance between 5,000 and 6,000 ohms?

Yes

GO to

E10

If the resistance is greater than 6,000 ohms, GO to

E12

. If the resistance is less than

5,000 ohms, GO to

E19

E10 CHECK POTENTIOMETER LOW SIDE RESISTANCE

Measure the resistance between EATC module C228a-20, circuit 438 (RD/WH)
and EATC module C228b-3, circuit 435 (YE/LB).

Is the resistance between 250 and 5,500 ohms?

Yes

GO to

E11

If the resistance is greater than 5,500 ohms, GO to

E14

. If the resistance is less than

250 ohms, GO to

E20

E11 CHECK POTENTIOMETER HIGH SIDE RESISTANCE

Measure the resistance between EATC module C228b-8, circuit 436 (RD/LG) and
EATC module C228b-3, circuit 435 (YE/LB).

Yes

GO to

E15

If the resistance is greater than 5,500 ohms, INSTALL a new door actuator. REFER to

Section 412-01

. CLEAR the DTCs. REPEAT the self-test. TEST the system for normal

operation. If the resistance is less than 250 ohms, GO to

E21

Page 17 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды

Lincoln 2006 Town Car, Руководство по ремонту

Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды