manualshive.com logo in svg

Lincoln 2006 Town Car, Руководство по ремонту

Руководство по ремонту Lincoln 2006 Town Car доступно для скачивания бесплатно на manualshive.com. Workshop manual поможет вам провести любые работы по обслуживанию и ремонту вашего автомобиля. Скачайте мануал прямо сейчас, чтобы быть в курсе всех технических аспектов вашего автомобиля.

Поделиться
Скачать
background image

  

Does the resistance smoothly increase and/or decrease when the jumpers are connected?

 

 

A8 CHECK THE ACTUATOR MOTOR DRIVE CIRCUITS FOR AN OPEN

 

NOTE: 

Due to limited connector accessibility, before carrying out this test step, visually inspect the 

wiring between the HVAC module and actuator for opens or shorts. If no damage is visually 
evident, proceed with the test. 

Ignition OFF.  

Disconnect: 

For DTC B2266

, LH Temperature Blend Door Actuator C2091.  

Disconnect: 

For DTC B2267

, RH Temperature Passenger Blend Door Actuator C2092. 

DTC B2266 

  

NOTE: 

For 

DTC B2266

 only.  

Measure the resistance between HVAC module C228a-26, circuit 245 (BN/LG), harness side and 
the LH temperature blend door actuator C2091-6, circuit 245 (BN/LG), harness side. 

DTC B2266 

  

NOTE: 

For 

DTC B2266

 only.  

Measure the resistance between HVAC module C228a-13, circuit 246 (VT), harness side and the 
LH temperature blend door actuator C2091-1, circuit 246 (VT), harness side. 

DTC B2267 

  

NOTE: 

For 

DTC B2267

 only.  

Measure the resistance between HVAC module C228a-12, circuit 1125 (BN), harness side and 
the RH temperature blend door actuator C2092-6, circuit 1125 (BN), harness side. 

DTC B2267 

Yes

 

INSPECT for binding or broken linkage. REPAIR as necessary. If no 
condition is found, INSTALL a new door actuator. TEST the system for 
normal operation.  
 

No

 

REPAIR the circuit(s) for an open. CLEAR the DTCs. REPEAT the self-
test. TEST the system for normal operation.

Page 8 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Отзывы:

Нет отзывов

Похожие инструкции для 2006 Town Car

iArmor IA-N179 Manual preview
IA-N179
Бренд: iArmor Страницы: 6
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Бренд: Pyle Страницы: 4
StowAway 2 025.41 Assembly Instructions preview
025.41
Бренд: StowAway 2 Страницы: 2
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Бренд: Ford Страницы: 256
Toyota CAMRY HV Manual preview
CAMRY HV
Бренд: Toyota Страницы: 636
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Yakima K896 Instructions Manual preview
K896
Бренд: Yakima Страницы: 12
Wagan Easy Air Auto Screen User Manual preview
Easy Air Auto Screen
Бренд: Wagan Страницы: 8
Mercedes-Benz CLS 2015 Operator'S Manual preview
CLS 2015
Бренд: Mercedes-Benz Страницы: 398
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Бренд: KLAUS Multiparking Страницы: 72
Honda Civic Hatch 2017 Owner'S Manual preview
Civic Hatch 2017
Бренд: Honda Страницы: 687
Wallbox PLP1 Installation Manual preview
PLP1
Бренд: Wallbox Страницы: 21
Mitsubishi Montero 1987 Service Manual preview
Montero 1987
Бренд: Mitsubishi Страницы: 284
Van Guard IN8377 Fitting Instructions Manual preview
IN8377
Бренд: Van Guard Страницы: 12
Chrysler 1953 Truck Owner'S Manual preview
1953 Truck
Бренд: Chrysler Страницы: 50
Sony Ericsson HCA-60 User Manual preview
HCA-60
Бренд: Sony Ericsson Страницы: 116
Toyota PZ403-B2614-GA Installation Instructions Manual preview
PZ403-B2614-GA
Бренд: Toyota Страницы: 12
Toyota handsfree communication User Manual preview
handsfree communication
Бренд: Toyota Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды