Lincoln 2006 Town Car Скачать руководство пользователя страница 14

Страница: 14 / 45

Is the resistance less than 5 ohms?

D4 CHECK CIRCUIT 676 (PK/OG) FOR AN OPEN

Measure the resistance between solar radiation sensor C287-2, circuit 676 (PK/OG)
and ground.

Is the resistance less than 5 ohms?

Yes

GO to

REPAIR circuit 676 (PK/OG) for an open. CLEAR the DTCs. REPEAT the self-test.
TEST the system for normal operation.

D5 CHECK CIRCUIT 468 (BN) AND 476 (BN/YE) FOR A SHORT TO CIRCUIT 676

(PK/OG)

Ignition OFF.

Disconnect: EATC Module C228b.

Measure the resistance between solar radiation sensor C287-1, circuit 468 (BN) and
C287-2, circuit 676 (PK/OG).

Measure the resistance between solar radiation sensor C287-6, circuit 476 (BN/YE)
and C287-2, circuit 676 (PK/OG).

Are the resistances greater than 10,000 ohms?

Yes

GO to

REPAIR circuit 468 (BN) or 476 (BN/YE) for a short to circuit 676 (PK/OG). CLEAR
the DTCs. REPEAT the self-test. TEST the system for normal operation.

D6 CHECK CIRCUIT 468 (BN) AND CIRCUIT 476 (BN/YE) FOR A SHORT TO GROUND

Measure the resistance between solar radiation sensor C287-1, circuit 468 (BN) and
ground.

Measure the resistance between solar radiation sensor C287-6, circuit 476 (BN/YE)
and ground.

Yes

GO to

REPAIR circuit 468 (BN) or 476 (BN/YE) for a short to ground. CLEAR the DTCs.
REPEAT the self-test. TEST the system for normal operation.

Page 14 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды

Lincoln 2006 Town Car, Руководство по ремонту

Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды