Lincoln 2006 Town Car Скачать руководство пользователя страница 6

Страница: 6 / 45

Is the resistance between 250 and 5,500 ohms?

A4 CHECK CIRCUITS 436 (RD/LG), 437 (YE/LG) AND 1122 (RD) FOR A SHORT TO GROUND

Measure the resistance between ground and the following:

HVAC module C228b-8, circuit 436 (RD/LG), harness side.

For DTC B2266

, HVAC module C228b-4, circuit 437 (YE/LG), harness side.

For DTC B2267

, HVAC module C228b-5, circuit 1122 (RD), harness side.

Is the resistance greater than 10,000 ohms?

Yes

GO to

REPAIR circuit(s) for a short to ground. CLEAR the DTCs. REPEAT the
self-test. TEST the system for normal operation.

A5 CHECK CIRCUITS 436 (RD/LG), 438 (RD/WH), 437 (YE/LG) AND 1122 (RD) FOR A SHORT TO

VOLTAGE

Measure the voltage between ground and the following:

HVAC module C228a-20, circuit 438 (RD/WH), harness side.

HVAC module C228b-8, circuit 436 (RD/LG), harness side.

For DTC B2266

, HVAC module C228b-4, circuit 437 (YE/LG), harness side.

For DTC B2267

, HVAC module C228b-5, circuit 1122 (RD), harness side.

Is any voltage present?

Yes

REPAIR circuit(s) for a short to voltage. CLEAR the DTCs. REPEAT the
self-test. TEST the system for normal operation.

For DTC B2266

,GO to

For DTC B2267

,GO to

A6 CHECK THE BLEND DOOR ACTUATOR OPERATION

NOTE:

If a jumper fuse opens while carrying out this test step, repair the circuit(s) for a short.

Ignition ON.

Measure the resistance between HVAC module C228b-4, circuit 437 (YE/LG), harness side and
HVAC module C228a-20, circuit 438 (RD/WH), harness side.

While observing the resistance, connect a fused jumper wire between:

HVAC module C228a-26, circuit 245 (BN/LG), harness side and HVAC module C228b-11,
circuit 1566 (RD/YE), harness side.

HVAC module C228a-13, circuit 246 (VT), harness side and HVAC module C228a-2, circuit
57 (BK), harness side.

Yes

INSPECT for broken door and linkage. REPAIR as necessary. If no
condition is found, GO to

GO to

Page 6 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды

Lincoln 2006 Town Car, Руководство по ремонту

Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды