Lincoln 2006 Town Car Скачать руководство пользователя страница 10

Страница: 10 / 45

Is the voltage between 4.7 and 5.1 volts?

B3 CHECK CIRCUIT 3058 (LG/RD) FOR AN OPEN

Ignition OFF.

Disconnect: EATC Module C228b.

Measure the resistance between EATC module C228b-19, circuit 3058 (LG/RD) and in-
vehicle temperature sensor C233-1, circuit 3058 (LG/RD).

Is the resistance less than 5 ohms?

Yes

GO to

REPAIR circuit 3058 (LG/RD) for an open. CLEAR the DTCs. REPEAT the self-
test. TEST the system for normal operation.

B4 CHECK CIRCUIT 3059 (YE/LG) FOR AN OPEN

Measure the resistance between EATC module C228b-16, circuit 3059 (YE/LG) and in-
vehicle temperature sensor C233-2, circuit 3059 (YE/LG).

Is the resistance less than 5 ohms?

Yes

GO to

REPAIR circuit 3059 (YE/LG) for an open. CLEAR the DTCs. REPEAT the self-
test. TEST the system for normal operation.

B5 CHECK CIRCUIT 3058 (LG/RD) FOR A SHORT TO CIRCUIT 3059 (YE/LG)

Ignition OFF.

Disconnect: EATC Module C228b.

Measure the resistance between in-vehicle temperature sensor C233-1, circuit 3058
(LG/RD) and C233-2, circuit 3059 (YE/LG).

Is the resistance greater than 10,000 ohms?

Yes

GO to

REPAIR circuit 3058 (LG/RD) for a short to circuit 3059 (YE/LG). CLEAR the
DTCs. REPEAT the self-test. TEST the system for normal operation.

B6 CHECK CIRCUIT 3058 (LG/RD) FOR A SHORT TO GROUND

Measure the resistance between EATC module C228b-19, circuit 3058 (LG/RD) and
ground.

Is the resistance greater than 10,000 ohms?

Yes

GO to

REPAIR circuit 3058 (LG/RD) for a short to ground. CLEAR the DTCs. REPEAT
the self-test. TEST the system for normal operation.

Page 10 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды

Lincoln 2006 Town Car, Руководство по ремонту

Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды