Lincoln 2006 Town Car Скачать руководство пользователя страница 19

Страница: 19 / 45

Measure the resistance between ground and EATC module C228b-3, circuit 435
(YE/LB).

Is the resistance greater than 10,000 ohms?

Yes

GO to

E17

REPAIR circuit 435 (YE/LB) for a short to ground. CLEAR the DTCs. REPEAT the self-
test. TEST the system for normal operation.

E17 CHECK CIRCUIT 436 (RD/LG) FOR A SHORT TO VOLTAGE

Ignition ON.

Measure the voltage between EATC module C228b-8, circuit 436 (RD/LG) and
ground.

Is voltage present?

Yes

REPAIR circuit 436 (RD/LG) for a short to voltage. CLEAR the DTCs. REPEAT the self-
test. TEST the system for normal operation.

GO to

E18

E18 CHECK CIRCUIT 435 (YE/LB) FOR A SHORT TO VOLTAGE

Measure the voltage between ground and EATC module C228b-3, circuit 435
(YE/LB).

Is voltage present?

Yes

REPAIR circuit 435 (YE/LB) for a short to voltage. CLEAR the DTCs. REPEAT the self-
test. TEST the system for normal operation.

INSPECT for binding or broken door and linkage. If no condition is found, GO to

E22

E19 CHECK CIRCUIT 438 (RD/WH) AND CIRCUIT 436 (RD/LG) FOR A SHORT

TOGETHER

Disconnect: Recirc Door Actuator C289.

Measure the resistance between EATC module C228a-20, circuit 438 (RD/WH)
and EATC module C228b-8, circuit 436 (RD/LG).

Is the resistance less than 5 ohms?

Yes

REPAIR circuits 438 (RD/WH) and circuit 436 (RD/LG) for a short together. CLEAR the
DTCs. REPEAT the self-test. TEST the system for normal operation.

INSTALL a new door actuator. REFER to

Section 412-01

. CLEAR the DTCs. REPEAT

the self-test. TEST the system for normal operation.

E20 CHECK CIRCUIT 438 (RD/WH) AND CIRCUIT 435 (YE/LB) FOR A SHORT

TOGETHER

Measure the resistance between EATC module C228a-20, circuit 438 (RD/WH)
and EATC module C228b-3, circuit 435 (YE/LB).

Yes

REPAIR circuits 438 (RD/WH) and circuit 435 (YE/LB) for a short together. CLEAR the
DTCs. REPEAT the self-test. TEST the system for normal operation.

INSTALL a new door actuator. REFER to

Section 412-01

. CLEAR the DTCs. REPEAT

the self-test. TEST the system for normal operation.

Page 19 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды

Lincoln 2006 Town Car, Руководство по ремонту

Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды