Lincoln 2006 Town Car Скачать руководство пользователя страница 7

Страница: 7 / 45

Remove the fused jumpers when the resistance does not change.

Connect a fused jumper wire between:

HVAC module C228a-13, circuit 246 (VT), harness side and HVAC module C228b-11,
circuit 1566 (RD/YE), harness side.

HVAC module C228a-26, circuit 245 (BN/LG), harness side and HVAC module C228a-2,
circuit 57 (BK), harness side.

Does the resistance smoothly increase and/or decrease when the jumpers are connected?

A7 CHECK THE BLEND DOOR ACTUATOR OPERATION

NOTE:

If a jumper fuse opens while carrying out this test step, repair the circuit(s) for a short.

Ignition ON.

Measure the resistance between HVAC module C228b-5, circuit 1122 (RD), harness side and
HVAC module C228a-20, circuit 438 (RD/WH), harness side.

While observing the resistance, connect a fused jumper wire between:

HVAC module C228a-12, circuit 1125 (BN), harness side and HVAC module C228b-11,
circuit 1566 (RD/YE), harness side.

HVAC module C228a-11, circuit 1124 (WH), harness side and HVAC module C228a-2,
circuit 57 (BK), harness side.

Remove the fused jumpers when the resistance does not change.

Connect a fused jumper wire between:

HVAC module C228a-11, circuit 1124 (WH), harness side and HVAC module C228b-11,
circuit 1566 (RD/YE), harness side.

HVAC module C228a-12, circuit 1125 (BN), harness side and HVAC module C228a-2,
circuit 57 (BK), harness side.

Yes

INSPECT for broken door and linkage. REPAIR as necessary. If no
condition is found, GO to

GO to

Page 7 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Содержание 2006 Town Car














































Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды

Lincoln 2006 Town Car, Руководство по ремонту

Результаты поиска

Содержание 2006 Town Car

Отзывы:

Похожие инструкции для 2006 Town Car

Бренды по названию

Популярные бренды