Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 56

Страница: 56 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

ENGINE GOVERNOR CONTROLLER (EGC) TEST PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This test will determine if the Engine Governor Controller (EGC) is functioning properly.

MATERIALS NEEDED

Volt/Ohmmeter

Wiring Diagram

TEST PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Open the side covers and secure them with the hooks provided.

Locate the engine governor controller (EGC) on the left rear side of the front panel. See

Figure F.18

See Wiring Diagram.

Place the ‘Run/Stop’ switch into the ‘Run’ position. Visually observe that the red LED on the engine

governor controller briefly illuminates. See

Figure F.18

. See Wiring Diagram.

Place the ‘Run/Stop’ switch into the ‘Stop’ position.

Using a volt/ohmmeter, perform the tests outlined in

Table F.1

. See

Figure F.19

. See Wiring

Diagram.

If any of the tests fail, the engine governor controller (EGC) may be faulty.

If faulty, perform the

Engine Governor Controller (EGC) Removal And Replacement Procedure

When testing is complete, close the side covers.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 56 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: